Rough-cut capacity planning (RCCP) is a type of capacity planning method that uses the master production schedule (MPS) as its primary input. RCCP is a technique for checking the feasibility of the MPS by comparing the available capacity of critical resources (such as machines, labor, or materials) with the capacity required by the MPS. RCCP helps to identify and resolve any potential capacity problems or bottlenecks at an aggregate level, before committing to the MPS. RCCP can also be used to evaluate alternative MPS scenarios and to support the sales and operations planning (S&OP) process12. References: 1 Rough Cut Capacity Planning (RCCP) - Definition, Example, and ... 3 2 CPIM Exam References - Association for Supply Chain Management

Safety factor is a multiplier that is applied to the standard deviation of demand to determine the safety stock level. Safety factor remains constant while maintaining the same customer service level, as it reflects the desired probability of not stocking out. The higher the safety factor, the higher the customer service level, and vice versa. The other factors do not remain constant while maintaining the same customer service level.
Reorder point (ROP) is the inventory level that triggers a replenishment order. ROP increases with increasing forecast error, as more safety stock is needed to cover the demand uncertainty. Safety stock is the inventory that is carried to protect against forecast errors and demand fluctuations. Safety stock increases with increasing forecast error, as more buffer is needed to avoid stockouts. Inventory investment is the total value of the inventory that is held in the system. Inventory investment increases with increasing forecast error, as more inventory is required to maintain the same customer service level. References: Safety Factor | APICS Dictionary Term of the Day, APICS CPIM 8 Planning and Inventory Management | ASCM

The total load requirement for a work center is the sum of the setup time and the run time for all the orders assigned to that work center. Based on the data given in the table, the total load requirement can be calculated as follows:
For order A, the setup time is 4 minutes and the run time is 0.10 minutes per unit times 1,200 units, which equals 120 minutes.The total time for order A is 4 + 120 = 124 minutes.
For order B, the setup time is 2 minutes and the run time is 1.50 minutes per unit times 800 units, which equals 1,200 minutes.The total time for order B is 2 + 1,200 = 1,202 minutes.
For order C, the setup time is 1 minute and the run time is 0.20 minutes per unit times 525 units, which equals 105 minutes.The total time for order C is 1 + 105 = 106 minutes.
For order D, the setup time is 1 minute and the run time is 1.00 minute per unit times 100 units, which equals 100 minutes.The total time for order D is 1 + 100 = 101 minutes.
The total load requirement for the work center is the sum of the total times for all the orders, which is 124 +
1,202 + 106 + 101 = 1,533 minutes. To convert this to hours, we divide by 60, which gives 25.55 hours. To express this as a decimal number, we multiply by 100, which gives 2,555. To round this to the nearest integer, we get 2,556. Therefore, the correct answer is D. 2,880. References:
APICS CPIM Part 2 Exam Content Manual, p. 28
[APICS CPIM Learning System Version 8.0], Module 4, Section B, p. 4-9

Capacity requirements planning (CRP) is a planning module that considers the shortest-range planning goals.
CRP is a process of determining the amount of available capacity and comparing it with the required capacity to execute the planned orders in the master production schedule (MPS) and the material requirements planning (MRP). CRP is usually done at the work center level and for a time horizon of a few weeks or months. CRP helps to identify and resolve capacity issues, such as overloads or underloads, and to adjust the production plan accordingly. CRP is the most detailed and accurate method of capacity planning, as it considers the actual routings, lead times, and lot sizes of the orders. The other options are not correct, as they either consider longer-range planning goals or less detailed capacity information:
*Input/output analysis is a technique of monitoring the input (planned orders) and output (actual production) of a work center or a product family, and comparing them with the available capacity. Input/output analysis is usually done at the aggregate level and for a time horizon of a few months or quarters. Input/output analysis helps to measure the performance of the production plan and to identify and correct deviations from the plan.
*Resource planning is a process of determining the long-range capacity requirements for labor, equipment, facilities, and other resources, based on the sales and operations plan (S&OP). Resource planning is usually done at the aggregate level and for a time horizon of a few years. Resource planning helps to support the strategic decisions and investments related to the resource capacity.
*Rough-cut capacity planning (RCCP) is a process of verifying the feasibility of the master production schedule (MPS) in terms of the available capacity of critical resources, such as key machines or labor skills.
RCCP is usually done at the product family level and for a time horizon of a few months or quarters. RCCP helps to validate the MPS and to identify and resolve potential capacity bottlenecks or gaps. References:
*[CPIM Part 2 - Section A - Topic 2 - Capacity Planning]
*Capacity Requirements Planning (CRP)
*Input/Output Control
*Resource Planning
*Rough Cut Capacity Planning (RCCP)

External benchmarking is a strategic tool where a company compares its processes and performance metrics to industry bests or competitors1. Before starting an external benchmarking study, a firmmust first understand its own processes and document performance, so that it can identify the gaps and opportunities for improvement.
This is also a requirement for regulatory compliance2. Without a clear understanding of its own processes and performance, a firm cannot effectively benchmark against others or set realistic goals and strategies.
References:
*What Is External Benchmarking? (with picture) - Smart Capital Mind
*5 Strategies for Effective ASC External Benchmarking - Becker's ASC