Online Access Free Cisco.200-101.v2021-12-02.q60 Practice Test (Page 6)

200-101 Exam Question 21

What command is used to verify the DLCI destination address in a Frame Relay static configuration?

A.show frame relay end-to-end

B.show frame-relay lmi

C.show frame-relay map

D.show frame-relay pvc

200-101 Exam Question 22

After the network has converged, what type of messaging, if any, occurs between R3 and R4?

A.No messages are exchanged.

B.Hellos are sent every 10 seconds.

C.The full database from each router is sent every 30 seconds.

D.The routing table from each router is sent every 60 seconds.

200-101 Exam Question 23

Which three statements about HSRP operation are true? (Choose three.)

A.HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing.

B.HSRP supports only clear-text authentication.

C.The virtual IP address and virtual MA+K44C address are active on the HSRP Master router.

D.The HSRP virtual IP address must be the same as one of the router's interface addresses on the LAN.

E.The HSRP virtual IP address must be on a different subnet than the routers' interfaces on the same LAN.

F.The HSRP default timers are a 3 second hello interval and a 10 second dead interval.

200-101 Exam Question 24

Refer to the exhibit.

What three actions will the switch take when a frame with an unknown source MAC
address arrives at the interface? (Select three.)

A.Write the MAC address to the startup-config.

B.Shut down the port.

C.Forward the traffic.

D.Increment the Security Violation counter.

E.Send an SNMP trap.

F.Send a syslog message.

200-101 Exam Question 25

Refer to the exhibit.

C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?

A.These commands need to be added to the configuration: C-router(config)# router rip C-router(config-router)# network 172.19.0.0

B.No further routing configuration is required.

C.These commands need to be added to the configuration: C-router(config)# router eigrp 123 C-router(config-router)# network 172.19.0.0

D.These commands need to be added to the configuration: C-router(config)# router ospf 1 C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0

Other Version: 1354Cisco.200-101.v2022-02-14.q60; 49Cisco.Pass4leader.200-101.v2022-02-05.by.wallis.60q.pdf; 70Cisco.Actual4labs.200-101.v2021-08-23.by.ivy.65q.pdf

Latest Upload: 119SAP.C_BCBAI_2509.v2026-01-15.q13; 198DAMA.DMF-1220.v2026-01-15.q271; 138SAP.C_SIGDA_2403.v2026-01-15.q66; 187ISACA.CRISC.v2026-01-15.q649; 128PaloAltoNetworks.NetSec-Pro.v2026-01-15.q26; 170Splunk.SPLK-1002.v2026-01-14.q121; 170EMC.NCP-AII.v2026-01-14.q144; 164Microsoft.AZ-800.v2026-01-13.q144; 176Microsoft.MS-102.v2026-01-13.q258; 121HP.HPE2-E84.v2026-01-13.q17

200-101 Exam Question 21

200-101 Exam Question 22

200-101 Exam Question 23

200-101 Exam Question 24

200-101 Exam Question 25

Download PDF File