300-410 Exam Question 301
Which IPv6 first hop security feature controls the traffic necessary for proper discovery of neighbor device operation and performance?
300-410 Exam Question 302
LAB SIMULATION 14
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
* Refer to the Tasks tab to view the tasks for this lab item.
* Refer to the Topology tab to access the device console(s) and perform the tasks.
* Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
* All necessary preconfigurations have been applied.
* Do not change the enable password or hostname for any device.
* Do not replace existing routing policies or configurations.
* Save your configurations to NVRAM before moving to the next item.
* Click Next at the bottom of the screen to submit this lab and move to the next question.
* When Next is clicked, the lab closes and cannot be reopened.
Topology
Tasks
Troubleshoot and resolve the issues on West and East routers to achieve these goals:
1. SW2 should only allow telnet access from ISP router's Loopback 0 using the AAA services. Fix the configs on SW2 to achieve this. Use preconfigured access-list ISP without removing the existing rule.
2. East router is configured to perform forwarding table lookup on an IP packet's source address, and it checks the incoming interface to reduce the risk of IP Address spoofing. Fix the issue where some East Router fails to ping destinations which are reachable via default route such as loopback 16 on ISP router. Do not advertise this interface into ospf and neither use a static route on East router to perform this task.
You must remove wrong preconfigs that have impact on tasks you are performing to fix issues.
Enable password is 'Cisco' on all devices
SW2: Local username is "SW2" and password is "Cisco"
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
* Refer to the Tasks tab to view the tasks for this lab item.
* Refer to the Topology tab to access the device console(s) and perform the tasks.
* Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
* All necessary preconfigurations have been applied.
* Do not change the enable password or hostname for any device.
* Do not replace existing routing policies or configurations.
* Save your configurations to NVRAM before moving to the next item.
* Click Next at the bottom of the screen to submit this lab and move to the next question.
* When Next is clicked, the lab closes and cannot be reopened.
Topology
Tasks
Troubleshoot and resolve the issues on West and East routers to achieve these goals:
1. SW2 should only allow telnet access from ISP router's Loopback 0 using the AAA services. Fix the configs on SW2 to achieve this. Use preconfigured access-list ISP without removing the existing rule.
2. East router is configured to perform forwarding table lookup on an IP packet's source address, and it checks the incoming interface to reduce the risk of IP Address spoofing. Fix the issue where some East Router fails to ping destinations which are reachable via default route such as loopback 16 on ISP router. Do not advertise this interface into ospf and neither use a static route on East router to perform this task.
You must remove wrong preconfigs that have impact on tasks you are performing to fix issues.
Enable password is 'Cisco' on all devices
SW2: Local username is "SW2" and password is "Cisco"
300-410 Exam Question 303
Refer to the exhibit. An engineer configured NetFlow on R1, but the flows do not reach the NMS server from R1.
Which configuration resolves this Issue?
Which configuration resolves this Issue?
300-410 Exam Question 304
Refer to the exhibit. The remote server is failing to receive the NetFlow data.
Which action resolves the issue?
Which action resolves the issue?
300-410 Exam Question 305
Refer to the exhibit. UserPC receives the IP address but does not register to the call manager.
Which command in ip dhcp pool VLAN200_USER_VOICE resolves the issue?
Which command in ip dhcp pool VLAN200_USER_VOICE resolves the issue?