Online Access Free Cisco.300-615.v2023-02-13.q50 Practice Test (Page 3)

300-615 Exam Question 6

Refer to the exhibit.

A network engineer is implementing a pair of Cisco Nexus 9000 Series Switches. During the OSPF configuration, the engineer discovers unstable routing in the network. The investigation shows flapping routes after the new switches were introduced. Which set of actions resolves the issue?

A.Configure a new OSPF priority on the Ethernet interface toward the OSPF neighbor. Clear the OSPF neighbor.

B.Configure a new IP address on the Ethernet interface toward the OSPF neighbor. Clear the OSPF process.

C.Configure a new IP address on the Loopback interface for the OSPF process. Clear the OSPF process

D.Configure a new IP address on the Ethernet interface toward the OSPF neighbor. Clear the OSPF neighbor.

300-615 Exam Question 7

An engineer is troubleshooting a packet flow from an access leaf to spine. Which EVPN routes are expected on this connection?

A.EVPN Type 9-15

B.EVPN Type 0,9,15

C.EVPN Type 0,16

D.EVPN Type 1-5

300-615 Exam Question 8

Refer to the exhibit.

A new Cisco Nexus 5548 Switch connects to a network. SAN switching is configured on the switch. The switch fc2/10 NP uplink is shown in the exhibit. Which action ensures that fc2/10 is in an up state?

A.Configure the BB_credit buffers on the upstream switch that connects the port.

B.Enable NPIV on the upstream switch that connects the port.

C.Configure the admin port type E on the upstream switch that connects the port.

D.Replace the SFP port module in fc2/10.

300-615 Exam Question 9

Refer to the exhibit.

An engineer configures the server port on a Cisco Nexus 5000 Series Switch. The switch connects to an NPV edge switch port. The server fails to send the FC traffic to the fabric. Which action resolves the issue?

A.Enable the NPIV mode on the Cisco Nexus 5000 switch.

B.Match the VSAN membership on both ends of the connection.

C.Configure the BB_credit buffer on the uplink port.

D.Replace the SFP in slot fc2/12.

300-615 Exam Question 10

A network engineer experiences the error "DDR3_P1_B1_ECC" when upgrading Cisco UCS firmware.
Which action resolves the issue?

A.Reset the BMC firmware

B.Reflash the DIMM

C.Reset the DIMM

D.Reflash the controller firmware

Other Version: 790Cisco.300-615.v2023-03-20.q63; 774Cisco.300-615.v2023-01-23.q51; 891Cisco.300-615.v2022-08-24.q43; 64Cisco.Validvce.300-615.v2022-04-14.by.robin.105q.pdf; 2058Cisco.300-615.v2022-01-19.q105; 2315Cisco.300-615.v2021-09-24.q100; 61Cisco.Itpassleader.300-615.v2021-08-05.by.kerr.91q.pdf

Latest Upload: 151CBIC.CIC.v2025-09-13.q75; 155Cisco.700-841.v2025-09-13.q131; 145SAP.C_ABAPD_2507.v2025-09-12.q56; 128SAP.C_TS452_2022.v2025-09-12.q83; 211ACSM.020-222.v2025-09-11.q48; 167VMware.5V0-31.23.v2025-09-10.q73; 138Oracle.1z0-915-1.v2025-09-10.q24; 174Citrix.1Y0-231.v2025-09-10.q87; 149SAP.C-THR85-2505.v2025-09-09.q29; 188Adobe.AD0-E727.v2025-09-09.q76

300-615 Exam Question 6

300-615 Exam Question 7

300-615 Exam Question 8

300-615 Exam Question 9

300-615 Exam Question 10

Download PDF File