Change the cables to fix physical connections is correct because the failure is tied to the UCS managed state of UCS, firmware, fabric interconnect. In Cisco UCS, policies are not advisory; they are the source from which fabric interconnects program adapters, boot targets, server identity, firmware, and external integrations.
A mismatch between the policy and the actual hardware or upstream storage/network state can cause boot, discovery, KVM, firmware, or connectivity failures. The selected action addresses the object that UCS Manager uses to build the final operational configuration. The distractors either solve a different fault domain or bypass the policy model. A disciplined DCIT validation sequence is to check the fault code, the FSM history, the equipment inventory, the service profile association, and the relevant adapter or boot table. If those states are correct after the change, the UCS component should return to operable service without unnecessary reconfiguration.

The correct action is the selected command set. Cisco UCS troubleshooting depends on the relationship between policy, inventory discovery, firmware state, and server identity. The question involves UCS, fabric interconnect, so the selected option fixes the UCS component or policy that directly controls the failure. In UCS Manager, service profiles, vNIC/vHBA templates, boot policies, firmware packages, server pools, adapters, fabric interconnects, and I/O modules are applied through a managed model; a server can fail even when basic IP reachability exists if the relevant policy is incomplete or the hardware inventory has not been acknowledged correctly. The distractors typically change an unrelated object, force a disruptive recovery without fixing the policy, or apply to a different UCS mode. Cisco guidance is to verify faults, FSM stage, inventory status, association status, and the specific boot or connectivity policy before taking action. After the remediation, validate that the fault clears, the FSM completes, and the server or fabric component returns to the expected operable state.

The selected answer, 1. Connect Fabric Interconnect B and execute "Erase configuration" 2. Reboot Fabric Interconnect B. 3. Add the subordinate Fabric Interconnect to the cluster, follows Cisco UCS operational logic. UCS Manager is policy-driven, so troubleshooting must determine whether the problem is caused by hardware discovery, service profile association, firmware activation, boot order, storage presentation, or management integration. The scenario points to fabric interconnect; that is why the selected action fixes the root condition rather than merely restarting the server. The wrong options either affect a different policy, require unnecessary disruption, or assume that physical connectivity alone is sufficient. Cisco documentation for UCS server boot and firmware management stresses that boot policies must include the correct target details, firmware workflows must complete their FSM stages, and hardware changes often require acknowledgement or re-acknowledgement before UCS Manager uses the new inventory. After remediation, the engineer should confirm that the UCS fault is cleared, the server association or discovery state is complete, and the operating system or management service can use the intended path.

Remove primaryEncap= " vlan-110 " from the specific port path is the required fix because the automation failure is caused by execution context, syntax, or resource state around APIC, EPG, Postman. On Cisco Nexus switches, automation is not a single feature; EEM policies, CLI actions, Guest Shell Linux commands, REST payloads, and scheduled jobs are evaluated by different subsystems. A script can fail even while the switch itself has connectivity or the command works interactively. The selected answer supplies the missing requirement, such as the correct event/action, DNS or resource setting, API URI, payload format, feature enablement, or reboot needed for a Guest Shell change to take effect. The other choices address adjacent features but do not satisfy the failing subsystem. After applying the fix, the engineer should verify the policy registration, job result, API response code, or Guest Shell runtime state and confirm that the intended command is no longer blocked or silently ignored.

Enable the NPIV mode on the Cisco Nexus 5000 switch is the correct fix under Cisco SAN troubleshooting practice. The issue described involves VSAN, NPIV, NPV, Cisco Nexus, where the operating state depends on the correct combination of port type, VSAN, fabric service, and access-control database. MDS and Nexus SAN features do not infer missing policy: if the active zoneset, fabric-binding database, fcdomain, NPIV setting, or FCoE/LLDP negotiation is wrong, the link may come up physically but the initiator will not reach the target. The selected answer corrects the missing or mismatched element. The remaining choices either act at the wrong layer, change a non-causal parameter, or provide only a temporary reset. After applying the fix, a proper Cisco validation path is to review show interface, show flogi database, show fcns database, show zoneset active, and any isolation or merge-failure logs. That confirms the storage network is operationally consistent.