Online Access Free Cisco.300-625.v2022-01-21.q72 Practice Test (Page 2)

300-625 Exam Question 1

Which configuration is needed to enable manual ESP mode for Fibre Channel TrustSec on Cisco MDS switches?

A.MDS(config)# interface fc 1/1
MDS(config-if)# fcsp esp manual

B.MDS(config)# fcsp esp manual

C.MDS(config)# interface fc 1/1
MDS(config-if)# fcsp mode gcm
MDS(config-if-fcsp)# fcsp esp manual

D.MDS(config)# interface fc 1/1
MDS(config-if)# fcsp esp manual
MDS(config-if-fcsp)# mode gcm

300-625 Exam Question 2

A Cisco MDS Series Switch with the POAP feature boots and does not find the startup configuration Which location is checked first when the switch enters POAP mode?

A.DHCP server to bootstrap the interface IP address, gateway, DNS server, and TFTP IP addresses

B.TFTP server where the necessary configuration files are downloaded

C.USB device that contains the software image files and the switch configuration file

D.HTTP server where the URL is used to download the software image

300-625 Exam Question 3

A storage engineer is troubleshooting a Cisco MDS switch upgrade issue. What prevents the completion of a non-d.sruptive upgrade?

A.The Fibre Channel storage target is connected.

B.The Fibre Channel and FCoE storage targets are connected.

C.The Fibre Channel host initiator is connected.

D.The Cisco Fabric Services operation in progress.

300-625 Exam Question 4

A storage network engineer must install and configure a new MDS switch in a data center network. Which two statements about available choices during the MDS switch initial setup are correct? (Choose two.)

A.The engineer can choose what will be the administrator account.

B.The secure password standard is required.

C.The engineer can configure the default zone policy.

D.The engineer can configure the default switch port trunk mode.

E.The engineer does not have the choice to enable or disable full zoneset distribution.

300-625 Exam Question 5

A storage administrator is connecting two previously configured switches to make a single fabric. When the E Ports are connected, the administrator sees a ZONE MERGE FAILURE message referring to the zoneset for VSAN 10 on each switch. Which command should the administrator use to allow these switches to work together?

A.zoneset import interface fc1/1 vsan 10

B.zoneset copy active-zoneset full-zoneset

C.zoneset distribute full vsan 10

D.zoneset overwrite-control vsan 10

Other Version: 55Cisco.Vceprep.300-625.v2022-03-29.by.vivien.72q.pdf; 1520Cisco.300-625.v2021-11-05.q69; 106Cisco.Updatedumps.300-625.v2021-08-16.by.harold.68q.pdf

Latest Upload: 148CBIC.CIC.v2025-09-13.q75; 150Cisco.700-841.v2025-09-13.q131; 145SAP.C_ABAPD_2507.v2025-09-12.q56; 128SAP.C_TS452_2022.v2025-09-12.q83; 211ACSM.020-222.v2025-09-11.q48; 166VMware.5V0-31.23.v2025-09-10.q73; 138Oracle.1z0-915-1.v2025-09-10.q24; 173Citrix.1Y0-231.v2025-09-10.q87; 148SAP.C-THR85-2505.v2025-09-09.q29; 187Adobe.AD0-E727.v2025-09-09.q76

300-625 Exam Question 1

300-625 Exam Question 2

300-625 Exam Question 3

300-625 Exam Question 4

300-625 Exam Question 5

Download PDF File