Online Access Free Cisco.350-401.v2025-12-28.q554 Practice Test (Page 21)

350-401 Exam Question 96

Which statement about VRRP is true?

A.It can be configured with HSRP on a switch or switch stack.

B.It supports IPv4 and IPv6.

C.It supports load balancing.

D.It supports encrypted authentication.

350-401 Exam Question 97

Refer to exhibit. What are two reasons for IP SLA tracking failure? (Choose two)

A.The destination must be 172.30.30.2 for icmp-echo

B.The threshold value is wrong

C.A route back to the R1 LAN network is missing in R2

D.The source-interface is configured incorrectly.

E.The default route has the wrong next hop IP address

Correct Answer: B,C

There is no problem with the Fa0/0 as the source interface as we want to check the ping from the LAN interface -> D is not correct.
Answer A is not correct as we must track the destination of the primary link, not backup link.
In this question, R1 pings R2 via its LAN Fa0/0 interface so maybe R1 (which is an ISP) will not know how to reply back as an ISP usually does not configure a route to a customer's LAN -> C is correct.
There is no problem with the default route -> E is not correct.
For answer B, we need to understand about how timeout and threshold are defined:
Timeout (in milliseconds) sets the amount of time an IP SLAs operation waits for a response from its request packet. In other words, the timeout specifies how long the router should wait for a response to its ping before it is considered failed.Threshold (in milliseconds too) sets the upper threshold value for calculating network monitoring statistics created by an IP SLAs operation.
Threshold is used to activate a response to IP SLA violation, e.g. send SNMP trap or start secondary SLA operation. In other words, the threshold value is only used to indicate over threshold events, which do not affect reachability but may be used to evaluate the proper settings for the timeout command.
For reachability tracking, if the return code is OK or OverThreshold, reachability is up; if not OK, reachability is down.
Therefore in this question, we are using "Reachability" tracking (via the command "track 10 ip sla
1 reachability") so threshold value is not important and can be ignored -> Answer B is correct. In fact, answer B is not wrong but it is the best option left.
This tutorial can help you revise IP SLA tracking topic: http://www.firewall.cx/cisco-technical- knowledgebase/cisco-routers/813-cisco-router-ipsla-basic.html and
http://www.ciscozine.com/using-ip-sla-to-change-routing/
Note: Maybe some of us will wonder why there are these two commands:
R1(config)#ip route 0.0.0.0 0.0.0.0 172.20.20.2 track 10
R1(config)#no ip route 0.0.0.0 0.0.0.0 172.20.20.2
In fact the two commands:
ip route 0.0.0.0 0.0.0.0 172.20.20.2 track 10
ip route 0.0.0.0 0.0.0.0 172.20.20.2
are different. These two static routes can co-exist in the routing table. Therefore if the tracking goes down, the first command will be removed but the second one still exists and the backup path is not preferred. So we have to remove the second one.

350-401 Exam Question 98

Which line must be added in the Python function to return the JSON object {"cat_9k":
"FXS1932Q2SE")?

A.return (json.dumps({for d in json.loads(test_json)['response']: d['hostname']: d['serialNumber']}))

B.return (json.dumps({d['hostname']: d['serialNumber'] for d in json.loads(test_json)['response']}))

C.return (json.loads({d['hostname']: d['serialNumber'] for d in json.dumps(test_json)['response'}))

D.return (json.loads({for d in json.dumps(test_json)['response']: d['hostname']: d['serialNumber']}))

350-401 Exam Question 99

Lab Simulation 30
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
- Refer to the Tasks tab to view the tasks for this lab item.
- Refer to the Topology tab to access the device console(s) and perform the tasks.
- Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
- All necessary preconfigurations have been applied.
- Do not change the enable password or hostname for any device.
- Save your configurations to NVRAM before moving to the next item.
- Click Next at the bottom of the screen to submit this lab and move to the next question.
- When Next is clicked, the lab closes and cannot be reopened.
Topology