350-501 Exam Question 71
Refer to the exihibit.
Refer to the exhibit. ISP A provides MPLS L3VPN service to customer A with BGP as the external routing protocol. Customer A has just opened a new branch office in London and requested the service provider to implement lossless service between its two offices. The LDP is enabled over the MPLS backbone and label exchange is working normally. Which action must the ISP engineering team take to enable the service?
Refer to the exhibit. ISP A provides MPLS L3VPN service to customer A with BGP as the external routing protocol. Customer A has just opened a new branch office in London and requested the service provider to implement lossless service between its two offices. The LDP is enabled over the MPLS backbone and label exchange is working normally. Which action must the ISP engineering team take to enable the service?
350-501 Exam Question 72
Refer to the exhibit.
Refer to the exhibit. The NOC is configuring PE router R4 for BGP-originated traffic. R4 is connected to a CE device at a customer location. The customer requires:
BGP peers must establish a neighborship with NSR and NSF capability.
BGP must maintain state with the CE and provide continuous forwarding during ISSU and RP switchover events.
Which action meets the NSR requirement on PE routers?
Refer to the exhibit. The NOC is configuring PE router R4 for BGP-originated traffic. R4 is connected to a CE device at a customer location. The customer requires:
BGP peers must establish a neighborship with NSR and NSF capability.
BGP must maintain state with the CE and provide continuous forwarding during ISSU and RP switchover events.
Which action meets the NSR requirement on PE routers?
350-501 Exam Question 73
Refer to the exhibit:
After implementing a new design for the network, a technician reviews the pictured CLI output as part of the MOP.
Which two statements describe what the technician can ascertain from the ImpNull output? (Choose two.)
After implementing a new design for the network, a technician reviews the pictured CLI output as part of the MOP.
Which two statements describe what the technician can ascertain from the ImpNull output? (Choose two.)
350-501 Exam Question 74
Refer to the exhibit.
Refer to the exhibit. A Tier-2 ISP provides MPLS Layer 3 VPNs to customers throughout the region. BGP and OSPF are used as routing protocols in the backbone, and all routers are running Cisco IOS-XE software. Customer A has requested a private connection between two of its offices. The company has plans to interconnect more offices across the country soon, so the solution should allow for the addition of new sites without reconfiguring the existing sites. The customer is using an IPv6 addressing scheme. R1 has been preconfigured with vrf definition Customer_A and assigned rd 1441:3421.
Which two tasks should the engineer perform on R1 to configure the private connection? (Choose two.)
Refer to the exhibit. A Tier-2 ISP provides MPLS Layer 3 VPNs to customers throughout the region. BGP and OSPF are used as routing protocols in the backbone, and all routers are running Cisco IOS-XE software. Customer A has requested a private connection between two of its offices. The company has plans to interconnect more offices across the country soon, so the solution should allow for the addition of new sites without reconfiguring the existing sites. The customer is using an IPv6 addressing scheme. R1 has been preconfigured with vrf definition Customer_A and assigned rd 1441:3421.
Which two tasks should the engineer perform on R1 to configure the private connection? (Choose two.)
350-501 Exam Question 75
Refer to the exhibit.
Refer to the exhibit. A network engineer just upgraded the Cisco IOS XE Software to the newest version on OSPF routers R1 and R2, added the point-to-point network type under Gi0/0 on R2, and configured ip route 192.168.10.0 255.255.255.0 192.168.1.2 on R1. After the engineer restarted the routers, R1 entered the Exstart state with its neighbor, but the adjacency has not been established. Which action must the engineer take to resolve the issue?
Refer to the exhibit. A network engineer just upgraded the Cisco IOS XE Software to the newest version on OSPF routers R1 and R2, added the point-to-point network type under Gi0/0 on R2, and configured ip route 192.168.10.0 255.255.255.0 192.168.1.2 on R1. After the engineer restarted the routers, R1 entered the Exstart state with its neighbor, but the adjacency has not been established. Which action must the engineer take to resolve the issue?