A bulge under the trackpad on a laptop is a strong and well-known indicator of a swollen lithium-ion battery.
According to CompTIA Core 1 (220-1201) mobile device hardware and troubleshooting objectives, laptop batteries are often located directly beneath the palm rest or trackpad area. When a lithium-ion battery begins to fail, it can swell due to internal chemical reactions, causing physical deformation of nearby components.
This swelling can interfere with the normal operation of the trackpad, leading to cursor control issues, clicking problems, or unresponsive behavior. More importantly, a swollen battery presents a serious safety risk, including the potential for overheating, leakage, or fire. For this reason, CompTIA emphasizes that battery replacement should be the first corrective action when physical swelling is observed.
Replacing the trackpad would not resolve the underlying pressure caused by the expanding battery. The motherboard and heat sink are unrelated to the physical bulge and cursor control symptoms described. Proper troubleshooting requires identifying and addressing the root cause, not the secondary symptom.
CompTIA best practices also stress safe handling and immediate replacement of damaged or swollen batteries to prevent further hardware damage or personal injury.
References:CompTIA A+ Core 1 (220-1201) Official Study Guide - Laptop Batteries, Mobile Device Troubleshooting, and Hardware Safety

A shutdown during POST combined with a burning smell strongly indicates an overheating condition occurring almost immediately after power-on. In a newly built workstation, the most common cause of rapid CPU overheating is improper heatsink installation, especially failing to apply thermal paste (thermal compound) between the CPU and the heatsink. Thermal paste fills microscopic imperfections between the two metal surfaces so heat can transfer efficiently into the heatsink. Without it, the CPU can spike to unsafe temperatures within seconds. Modern systems detect this and trigger protective thermal shutdown during POST to prevent permanent CPU or motherboard damage. The burning smell can occur when components near the CPU socket heat excessively or when protective coatings/dust residues warm quickly due to poor heat dissipation.
The wrong type of RAM (B) would more likely cause no-boot/beep codes rather than a burning smell. Not properly grounding (A) relates to ESD damage risk, but that typically causes intermittent or dead hardware symptoms, not immediate thermal shutdown. A disconnected case exhaust fan (C) can contribute to higher case temperatures, but it's less likely to cause an immediate POST shutdown compared to missing thermal paste on the CPU cooler.

This scenario describes disk mirroring, which is RAID 1. With RAID 1, the same data is written to two drives simultaneously, creating an exact duplicate on each SSD. If one drive fails, the system can continue to operate using the remaining drive with no loss of data, which directly matches the requirement "no data loss if one drive fails." RAID 1 is commonly used when fault tolerance and data redundancy are the priority. A key trade- off is capacity: because the data is duplicated, the usable storage is essentially the size of one of the drives (two 1TB drives in RAID 1 provide about 1TB usable). Performance can vary: read performance may improve slightly in some implementations, but write performance is generally similar to a single drive because data must be written to both drives.
RAID 0 is striping with no redundancy, so a single drive failure causes total data loss. RAID 5 requires at least three drives and uses parity. RAID 10 requires at least four drives and combines mirroring and striping.
Therefore, the correct answer is RAID 1.

To allow multiple users to print to networked printers:
Printer shares enable users to access printers shared on the network.
Print servers manage print jobs and provide centralized control of printing.
Why Not B (DHCP server): DHCP is unrelated to print management.
Why Not D (Printer subnet): Subnets group devices but don't manage printing.
Why Not E (SMB configuration): SMB is for file sharing, not specifically print management.
Why Not F (Printer Wi-Fi settings): These settings are irrelevant since the printers use Ethernet.
CompTIA A+ Exam Reference: Core 2 (220-1102), Section 4.6, printer configuration.

CompTIA A+ divides hypervisors into two main categories: Type 1 (bare-metal) and Type 2 (hosted). A Type
2 hypervisor runs on top of an existing host operating system such as Windows, macOS, or Linux. It relies on the host OS for device drivers, hardware interaction, and resource management. Examples include VMware Workstation, Oracle VirtualBox, and Parallels Desktop.
Type 2 hypervisors are ideal for lab environments, testing, learning, and small-scale virtualization because they do not require dedicated hardware or direct hardware control. The host OS loads first, and the hypervisor runs as an application, allowing users to create and manage virtual machines from within the OS environment.
Option B describes a Type 1 hypervisor, which installs directly on hardware without a host OS. Option A is unrelated, as firewalls are separate from virtualization technology. Option D is incorrect because hypervisors do not inherently increase CPU capabilities; they merely allocate existing hardware resources to virtual machines.
Thus, the correct and CompTIA-aligned description of a Type 2 hypervisor is that it runs on a host operating system.