The correct answer is EOL discontinues the product but may offer support. According to CompTIA Network+ (N10-009) objectives related to lifecycle management and vendor support policies, End of Life (EOL) indicates that a product is no longer being manufactured or sold by the vendor. However, after EOL is declared, the vendor may continue to provide limited support, updates, or warranty services for a defined period.
In contrast, End of Support (EOS) means the vendor has stopped providing technical assistance, patches, firmware updates, and security fixes for the product. Once a product reaches EOS, organizations are responsible for maintaining it without vendor assistance, which can introduce operational and security risks.
Option B is incorrect because EOS does not typically convert support into a subscription model-it signifies the termination of support. Option C is incorrect because EOS applies to both hardware and software products. Option D is incorrect because warranty terms depend on vendor policy and are not guaranteed after EOL status.
Therefore, the key distinction is that EOL ends product sales, while EOS ends vendor support.

Power over Ethernet (PoE) allows devices such as cameras, access points, and VoIP phones to receive both power and data over the same Ethernet cable. If only eight out of twelve cameras turn on, the most likely issue is that the PoE switch has exceeded its power budget (total wattage capacity).
PoE Budget Limitation: PoE switches have a maximum power output, which can limit the number of devices they support simultaneously.
Voltage Check: Different PoE standards exist:
802.3af (PoE): Supplies up to 15.4W per port
802.3at (PoE+): Supplies up to 30W per port
802.3bt (PoE++): Supplies up to 60-100W per port
Power Draw Calculation: If each camera requires 15W and the switch can only provide 120W, then only 8 cameras (8 × 15W = 120W) will turn on.
Incorrect Options:
A). Ethernet Cable Type: Most PoE devices work with Cat5e and above. Cable type could be an issue, but power limitation is the more immediate concern.
C). Transceiver Compatibility: Only relevant if fiber transceivers or modules are in use, but not likely the root cause for power-related issues.
D). DHCP Addressing: DHCP issues affect network connectivity, not power delivery.
Reference:
CompTIA Network+ N10-009 Official Study Guide - Chapter on Power over Ethernet (PoE)

An802.11ac wireless bridgeis the most practical solution to connect two nearby buildingswithout trenching or laying physical cable. It provides high-speed, point-to-point connectivity using directional antennas.
* A. Multimode fiberis effective but expensive and typically limited to 500 meters or less.
* C. Cat 6 copperis only rated for up to 100 meters - not viable for a street-wide distance.
* D. Loopback adapteris a troubleshooting tool, not for network extension.
#Reference:
CompTIA Network+ N10-009 Official Objectives: 1.3 - Compare and contrast various network topologies, types, and technologies.

See the solution below in Explanation.
Explanation:
To provide a complete solution for configuring the access layer switches, let's proceed with the following steps:
Identify the correct VLANs for each device and port.
Enable necessary ports and disable unused ports.
Configure fault-tolerant connections between the switches.
Port 1 Configuration (Uplink to Core Switch)
Status: Enabled
LACP: Enabled
Speed: 1000
Duplex: Full
VLAN Configuration: Tagged for VLAN60, VLAN90, VLAN120, VLAN150, VLAN220 Port 2 Configuration (Uplink to Core Switch) Status: Enabled LACP: Enabled Speed: 1000 Duplex: Full VLAN Configuration: Tagged for VLAN60, VLAN90, VLAN120, VLAN150, VLAN220 Port 3 Configuration (Server Connection) Status: Enabled LACP: Disabled Speed: 1000 Duplex: Full VLAN Configuration: Untagged for VLAN90 (Servers) Port 4 Configuration (Server Connection) Status: Enabled LACP: Disabled Speed: 1000 Duplex: Full VLAN Configuration: Untagged for VLAN90 (Servers) Port 5 Configuration (Wired Users and WLAN) Status: Enabled LACP: Enabled Speed: 1000 Duplex: Full VLAN Configuration: Tagged for VLAN60, VLAN120, VLAN150 Port 6 Configuration (Wired Users and WLAN) Status: Enabled LACP: Enabled Speed: 1000 Duplex: Full VLAN Configuration: Tagged for VLAN60, VLAN120, VLAN150 Port 7 Configuration (Voice and Wired Users) Status: Enabled LACP: Enabled Speed: 1000 Duplex: Full VLAN Configuration: Tagged for VLAN60, VLAN90, VLAN120, VLAN220 Port 8 Configuration (Voice, Printers, and Wired Users) Status: Enabled LACP: Enabled Speed: 1000 Duplex: Full VLAN Configuration: Tagged for VLAN60, VLAN90, VLAN120, VLAN220 Port 1 Configuration (Unused) Status: Disabled LACP: Disabled Port 2 Configuration (Unused) Status: Disabled LACP: Disabled Port 3 Configuration (Connection to Device) Status: Enabled LACP: Disabled Speed: 1000 Duplex: Full VLAN Configuration: Untagged for VLAN1 (Default) Port 4 Configuration (Connection to Device) Status: Enabled LACP: Disabled Speed: 1000 Duplex: Full VLAN Configuration: Untagged for VLAN1 (Default) Port 5 Configuration (Connection to Device) Status: Enabled LACP: Disabled Speed: 1000 Duplex: Full VLAN Configuration: Untagged for VLAN1 (Default) Port 6 Configuration (Connection to Device) Status: Enabled LACP: Disabled Speed: 1000 Duplex: Full VLAN Configuration: Untagged for VLAN1 (Default) Port 7 Configuration (Connection to Device) Status: Enabled LACP: Disabled Speed: 1000 Duplex: Full VLAN Configuration: Untagged for VLAN1 (Default) Ports 1 and 2 on Switch 1 are configured as trunk ports with VLAN tagging enabled for all necessary VLANs.
Ports 3 and 4 on Switch 1 are configured for server connections with VLAN 90 untagged.
Ports 5, 6, 7, and 8 on Switch 1 are configured for devices needing access to multiple VLANs.
Unused ports on Switch 3 are disabled.
Ports 3, 4, 5, 6, and 7 on Switch 3 are enabled for default VLAN1.
Core Switch Ports should be configured as needed for uplinks to Switch 1.
Ensure LACP is enabled for redundancy on trunk ports between switches.
By following these configurations, each device will access only its correctly associated network, unused switch ports will be disabled, and fault-tolerant connections will be established between the switches.