Explanation
A warm site is a type of disaster recovery site that has a target storage array that receives replication traffic and servers that are only powered on in the event of a disaster. A warm site is a compromise between a hot site and a cold site. A warm site has some equipment and data ready, but requires some configuration and restoration before resuming operations. A warm site is usually located in a different geographic area than the primary site and has redundant power, cooling, network, and security systems. A warm site is suitable for organizations that can tolerate some downtime and data loss in case of a disaster. A cloud site is a type of disaster recovery site that uses cloud-based resources and platforms to store backups and restore data and applications after a disaster. A cold site is a type of disaster recovery site that has only basic infrastructure and space available, but requires significant setup and installation before resuming operations. A hot site is a type of disaster recovery site that has all the equipment and data ready to resume operations as soon as possible after a disaster.
References: https://www.techopedia.com/definition/11172/hot-site
https://www.techopedia.com/definition/11173/warm-site
https://www.techopedia.com/definition/11174/cold-sitehttps://www.techopedia.com/definition/29836/cloud-reco

RAID 1 (mirroring) is a RAID configuration that should be used to provide redundancy for the OS on a server that has two hard drives on which to install the OS. RAID 1 (mirroring) is a configuration that duplicates data across two or more drives. It provides fault tolerance and improves read performance, but reduces storage capacity by half. If one drive fails in RAID 1, the other drive can continue to operate without data loss or system downtime. RAID 0 (striping) is a configuration that splits data across two or more drives without parity or redundancy. It improves performance but offers no fault tolerance. If one drive fails in RAID 0, all data is lost and the system cannot boot. RAID 5 (striping with parity) is a configuration that stripes data across three or more drives with parity information. It provides fault tolerance and improves performance, but reduces storage capacity by one drive's worth of space. RAID 5 can tolerate one drive failure without data loss, but not two or more. RAID 6 (striping with double parity) is a configuration that stripes data across four or more drives with double parity information. It provides fault tolerance and improves performance, but reduces storage capacity by two drives' worth of space. RAID 6 can tolerate two drive failures without data loss, but not three or more. References:
https://www.howtogeek.com/199068/how-to-upgrade-your-existing-hard-drive-in-under-an-hour/

Shell is the most appropriate scripting language to use for a logon script for a Linux box. Shell is a generic term for a command-line interpreter that allows users to interact with the operating system by typing commands and executing scripts. Shell scripts are files that contain a series of commands and instructions that can be executed by a shell. Shell scripts are commonly used for automating tasks, such as logon scripts that run when a user logs on to a system. There are different types of shells available for Linux systems, such as Bash, Ksh, Zsh, etc., but they all share a similar syntax and functionality.

The IP address/default gateway combination that the administrator should have used for the new server is IP address: 192.168.10.2/24 and Default gateway: 192.168.10.1.
The IP address and the default gateway of a device must be in the same subnet to communicate with each other.
A subnet is a logical division of a network that allows devices to share a common prefix of their IP addresses.
The subnet mask determines how many bits of the IP address are used for the network prefix and how many bits are used for the host identifier. A /24 subnet mask means that the first 24 bits of the IP address are used for the network prefix and the last 8 bits are used for the host identifier. Therefore, any IP address that has the same first 24 bits as the default gateway belongs to the same subnet. In this case, the default gateway has an IP address of 192.168.10.1/24, which means that any IP address that starts with 192.168.10.x/24 belongs to the same subnet. The new server has an IP address of 192.168.1.1/24, which does not match the first 24 bits of the default gateway, so it belongs to a different subnet and cannot communicate with the default gateway. To fix this issue, the administrator should change the IP address of the new server to an unused IP address that starts with 192.168.10.x/24, such as 192.168.10.2/24.

Port 443 is the default port for HTTPS, which is the protocol used for secure web communication. HTTPS uses SSL/TLS certificates to encrypt the data between the web server and the browser. Port 443 is commonly used for web servers that need to provide secure services, such as online banking, e-commerce, or email. By allowing port 443, the administrator can access the web server's interface and manage its settings1.
Port 3389 is the default port for RDP, which is the protocol used for remote desktop connection. RDP allows a user to remotely access and control another computer over a network. Port 3389 is commonly used for remote administration, technical support, or remote work. By allowing port 3389, the administrator can connect to the web server's desktop and perform tasks that require graphical user interface2.