Explanation
The most likely cause of the issue is that two default routes are configured on the server. The default route is the route that is used when no other route matches the destination of a packet. The default route is usually the gateway that connects the local network to the Internet. The server configuration shows that there are two default routes in the routing table, one with the gateway 192.168.1.1 and the other with the gateway 10.0.0.1.
This can cause a conflict and confusion for the server when deciding which gateway to use for the outgoing packets. Some packets may be sent to the wrong gateway and fail to reach the Internet, while some packets may be sent to the correct gateway and work as intended. This can result in intermittent connection issues and inconsistent behavior. The administrator should remove one of the default routes and keep only the correct one for the network. This can be done by using the ip route del command or by editing the network configuration files. This will resolve the issue and restore the connectivity. The other options are incorrect because they are not supported by the outputs. The DNS server, the IP netmask, and the ARP table are not the causes of the issue. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 12: Managing Network Connections, pages 381-382.

Explanation
The issue is caused by the lack of a default route defined in the /etc/sysconfig/network-scripts/ifcfg-enp0s3 file. A default route is a special route that specifies where to send packets that do not match any other routes in the routing table. Without a default route, the server will not be able to communicate with hosts outside its local network. The default route is usually configured with the GATEWAY option in the network interface configuration file. For example, to set the default gateway to 192.168.1.1, the file should contain:
GATEWAY=192.168.1.1
The other options are not causing the issue. The DNS address is not commented out in the configuration file, it is specified with the DNS1 option. The search entry in the /etc/resolv.conf file is correct, it specifies the domain name to append to unqualified hostnames. Wired connection 1 is online, as indicated by the ONBOOT=yes option and the output of ip link show enp0s3 command. References: Configuring IP Networking with nmcli; Configuring IP Networking with ifcfg Files

Explanation
The command that will allow the systems administrator to check whether the system supports virtualization is lscpu. This command will display information about the CPU architecture, such as the number of CPUs, cores, sockets, threads, model name, frequency, cache size, and flags. One of the flags is vmx (for Intel processors) or svm (for AMD processors), which indicates that the CPU supports hardware virtualization. If the flag is present, it means that the system supports virtualization. If the flag is absent, it means that the system does not support virtualization or that it is disabled in the BIOS settings.
The other options are not correct commands for checking whether the system supports virtualization. The dmidecode -s system-version command will display the version of the system, such as the product name or serial number, but not the CPU information. The sysctl -a command will display all the kernel parameters, but not the CPU flags. The cat /sys/devices/system/cpu/possible command will display the range of possible CPUs that can be online or offline, but not the CPU features. References: lscpu(1) - Linux manual page; How To Check If Virtualization is Enabled in Windows 10 / 11

Explanation
The tuned application is the best tool for dynamic tuning of kernel parameters, as it monitors the system and optimizes the performance under different workloads. It provides a number of predefined profiles for typical use cases, such as power saving, low latency, high throughput, virtual machine performance, and so on. It also allows users to create, modify, and delete profiles, and to switch between them on the fly. The tuned application uses the sysctl command and the configuration files in the /etc/sysctl.d/ directory to adjust the kernel parameters at runtime.
References
Chapter 2. Getting started with TuneD - Red Hat Customer Portal, paragraph 1 Kernel tuning with sysctl - Linux.com, paragraph 1

Explanation
The command tail -n 20 will display the last 20 lines of a file. The -n option specifies the number of lines to show. This is the correct command to execute the task. The other options are incorrect because they either use the wrong options (-v, -c, or -l) or have the wrong arguments (20 instead of 20 filename). References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 11: Managing Files and Directories, page 352.