Explanation
The firewall-cmd --list-services command will return the results for which the administrator is looking. This command will list all services that are allowed through the firewall in the default zone or a specified zone. A service is a predefined set of ports and protocols that can be enabled or disabled by firewalld. The firewall-cmd --get-services command will list all available services that are supported by firewalld, not only those that are allowed through the firewall. The firewall-cmd --check-config command will check if firewalld configuration files are valid, not listservices. The systemctl status firewalld command will display information about the firewalld service unit, such as its state, PID, memory usage, and logs, not list services. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 18: Securing Linux Systems, page 543.

Explanation
The systemctl reload sshd command can be used to apply the configuration changes of the SSH server daemon without restarting it. This is useful to avoid interrupting existing connections. The systemctl stop sshd command would stop the SSH server daemon, not apply the changes. The systemctl mask sshd command would prevent the SSH server daemon from being started, not apply the changes. The systemctl start sshd command would start the SSH server daemon if it is not running, but it would not apply the changes if it is already running. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 12: Secure Shell (SSH), page 415.

Explanation
The parameter net.ipv4.ip_forward=1 will accomplish the goal of setting up a new Linux server as a router.
This parameter enables the IP forwarding feature, which allows the server to forward packets between different network interfaces. This is necessary for a router to route traffic between different networks. The parameter can be set in the /etc/sysctl.conf file or by using the sysctl command. This is the correct parameter to use to accomplish the goal. The other options are incorrect because they either do not exist(net.ipv4.ip_forwarding or net.ipv4.ip_route) or do not enable IP forwarding (net.ipv4.ip_forward=0). References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 12:
Managing Network Connections, page 382.

Explanation
The command iptables -t filter -A INPUT -p tcp --dport 4000:5000 -j ACCEPT will enforce the rule of allowing incoming traffic to ports in the range of 4000 to 5000 on a Linux server. The iptables command is a tool for managing firewall rules on Linux systems. The -t option specifies the table to operate on, in this case filter, which is the default table that contains the rules for filtering packets. The -A option appends a new rule to the end of a chain, in this case INPUT, which is the chain that processes the packets that are destined for the local system. The -p option specifies the protocol to match, in this case tcp, which is thetransmission control protocol. The --dport option specifies the destination port or port range to match, in this case 4000:5000, which is the range of ports from 4000 to 5000. The -j option specifies the target to jump to if the rule matches, in this case ACCEPT, which is the target that allows the packet to pass through. The command iptables -t filter -A INPUT -p tcp --dport 4000:5000 -j ACCEPT will add a new rule to the end of the INPUT chain that will accept the incoming TCP packets that have a destination port between 4000 and
5000. This command will enforce the rule and allow the traffic to the specified ports. This is the correct command to use to accomplish the task. The other options are incorrect because they either use the wrong options (-f instead of -t or -D instead of -A) or do not exist (iptables filter -A INPUT -p tcp --dport 4000:5000
-D ACCEPT or iptables filter -S INPUT -p tcp --dport 4000:5000 -A ACCEPT). References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 18: Securing Linux Systems, page 543.

Explanation
The administrator should add REQUIRES=mariadb.service to the HTTP server .service file to ensure that the database is available before the web application is started. This directive specifies that the HTTP server unit requires the MariaDB server unit to be started before it can run. If the MariaDB server unit fails to start or stops for any reason, the HTTP server unit will also fail or stop. This way, the dependency between the web application and the database is enforced by systemd.
The other options are not correct directives for accomplishing this task. TRIGGERS=mariadb.service is not a valid directive in systemd unit files. ONFAILURE=mariadb.service means that the HTTP server unit will start only if the MariaDB server unit fails, which is not what we want. WANTEDBY=mariadb.service means that the HTTP server unit will be started when the MariaDB server unit is enabled, but it does not imply a strong dependency or ordering relationship between them. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 10: Managing Services with systemd; systemd.unit(5) - Linux manual page