The networking is shown in the figure, RTA learns the 10.1.1.0/24 route through OSPF 100, and uses network to import BGP.
View the 10.1.1.0/24 route on the RTA, and the results are as follows:
RTA]displaip routing-table 10.1.1.0
Destination/Mask Protocol Pre Cost Nexthop Interface
10.1.1.0/24 OSPF 10 2 1.1.1.2 Ethernet0/0
Configure default med 200 on RTA. Please visit the BGP routing table of RTA. What is the MED attribute value of 10.1.1.0/24?

As shown in the figure, RTA and RTB are connected by IPv6 Over IPv4 manual tunnel, and OSPFv3 is run on each IPv6 interface, then there are ______ IPv6 routes learned by OSPFv3 on RTA.

In OSPF, the types of LSAs that cannot be aggregated by ASBR are _______

In the topology shown in the figure, the following configurations are performed on RTA, RTB, RTC and RTD respectively:
RTA] ospf 1 router-id 1.1.1.1
RTA-ospf-1] area 0
RTA-ospf-1-area-0.0.0.0] network 192.168.1.0 0.0.0.255
RTA-ospf-1-area-0.0.0.0] network 1.1.1.1 0.0.0.0
RTB] ospf 1 router-id 2.2.2.2
RTB-ospf-1] area 0
RTB-ospf-1-area-0.0.0.0] network 192.168.1.0 0.0.0.255
RTB-ospf-1-area-0.0.0.0] network 2.2.2.2 0.0.0.0
RTB-ospf-1] area 1
RTB-ospf-1-area-0.0.0.1] network 192.168.2.0 0.0.0.255
RTB-ospf-1-area-0.0.0.1] vlink-peer 3.3.3.3
RTC] ospf 1 router-id 3.3.3.3
RTC-ospf-1] area 1
RTC-ospf-1-area-0.0.0.1] network 192.168.2.0 0.0.0.255
RTC-ospf-1-area-0.0.0.1] network 3.3.3.3 0.0.0.0
RTC-ospf-1-area-0.0.0.1] vlink-peer 2.2.2.2
RTC-ospf-1] area 2
RTC-ospf-1-area-0.0.0.2] network 192.168.3.0 0.0.0.255
RTD] ospf 1 router-id 4.4.4.4
RTD-ospf-1] area 2
RTD-ospf-1-area-0.0.0.2] network 192.168.3.0 0.0.0.255
RTD-ospf-1-area-0.0.0.2] network 4.4.4.4 0.0.0.0
Then the router type in the RTC in the OSPF area is _______

In the topology shown in the figure, perform the following configurations on RTA, RTB, and RTC respectively:
RTA-GigabitEthernet0/0] ip address 192.168.2.1 255.255.255.0
RTA] ospf 1 router-id 1.1.1.1
RTA-ospf-1] area 1
RTA-ospf-1-area-0.0.0.1] network 192.168.2.0 0.0.0.255
RTB-GigabitEthernet0/0] ip address 192.168.2.2 255.255.255.0
RTB-GigabitEthernet0/1] ip address 192.168.3.1 255.255.255.0
RTB] ospf 1 router-id 2.2.2.2
RTB-ospf-1] area 1
RTB-ospf-1-area-0.0.0.1] network 192.168.2.0 0.0.0.255
RTB-ospf-1] area 0
RTB-ospf-1-area-0.0.0.0] network 192.168.3.0 0.0.0.255
RTB-ospf-1]import-route direct
RTC-GigabitEthernet0/0] ip address 192.168.3.2 255.255.255.0
RTC] ospf 1 router-id 3.3.3.3
RTC-ospf-1] area 0
RTC-ospf-1-area-0.0.0.0] network 192.168.3.0 0.0.0.255
Then the LSA types generated by RTB in the OSPF area are _______