Online Access Free HP.HPE6-A72.v2025-01-13.q55 Practice Test (Page 9)

HPE6-A72 Exam Question 36

Refer to the exhibit

Which command on Access-2 port 1/1/4 will enable connectivity between PC-1 and Server-1 without any routing enabled in the network?

A.Access-2 (config-if-1/1/4)# vlan 20 untag 1/1/4

B.Access-2 (config-if-1/1/4)# vlan access 1, 10, 20, 255

C.Access-2 (config-if-1/1/4)# vlan access 20

D.Access-2 (config-if-1/1/4)# vlan trunk allow 1, 10, 255

HPE6-A72 Exam Question 37

Refer to the exhibit

What is true regarding VLAN 50 according to the diagram above?

A.VLAN 50 is part of a switched virtual interface (SVI) that was never routed causing it to be down.

B.Since VLAN 50 has not been assigned to any enabled physical port, the status is down.

C.VLAN 50 is assigned only to Trunk ports which is why no ports are listed under interfaces.

D.VLAN 50 was never added to the vlan-database and therefore is in a down state.

HPE6-A72 Exam Question 38

Click on the colored box that corresponds with the line that best represents Multicast traffic flow.

HPE6-A72 Exam Question 39

Refer to the exhibit.

You are in the process of configuring VSF between Access-1 and Access-2. Access-1 has been configured as the VSF Master. What is a valid configuration for Access-2 to join the VSF stack?

A.Access-2# configure
Access-2(config)# vsf member 1
Access-2(vsf-member-1)# link 1 1/1/28
Access-2(vsf-member-1)# exit
Access-2(config)# vsf renumber-to 2
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y

B.Access-2# configure
Access-2(config)# vsf member 1
Access-2(config)# vsf renumber-to 2
Access-2(vsf-member-1)# link 2 2/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y

C.Access-2# configure
Access-2(config># vsf member 2
Access-2(vsf-member-1)# link 2 1/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y

D.Access-2# configure
Access-2(config)# vsf member 2
Access-2(vsf-member-1)# link 1 1/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y

HPE6-A72 Exam Question 40

Which command can be used to find the serial number of an Aruba OS-CX switch?

A.The command inventory

B.The command version

C.The command show running-configuration

D.The command show system

Other Version: 809HP.HPE6-A72.v2022-11-26.q37; 96HP.Actualtests4sure.HPE6-A72.v2022-04-27.by.lesley.38q.pdf; 1848HP.HPE6-A72.v2022-02-04.q38; 1827HP.HPE6-A72.v2021-11-06.q37

Latest Upload: 150Pegasystems.PEGACPDC25V1.v2026-07-17.q45; 249CompTIA.N10-009.v2026-07-17.q230; 171EMC.D-PDM-DY-23.v2026-07-17.q66; 165Salesforce.ADM-201.v2026-07-17.q63; 406PMI.CAPM.v2026-07-17.q643; 169Cisco.300-215.v2026-07-17.q60; 454CollegeAdmission.PMHNP.v2026-07-17.q640; 232Microsoft.MB-240.v2026-07-17.q174; 144SAP.C_CE325_2601.v2026-07-17.q37; 302Microsoft.AZ-900.v2026-07-16.q224

HPE6-A72 Exam Question 36

HPE6-A72 Exam Question 37

HPE6-A72 Exam Question 38

HPE6-A72 Exam Question 39

HPE6-A72 Exam Question 40

Download PDF File