Explanation/Reference:
A momentary low voltage is a sag. A synonym would be a dip.
Risks to electrical power supply:
POWER FAILURE
Blackout: complete loss of electrical power
Fault: momentary power outage
POWER DEGRADATION
Brownout: an intentional reduction of voltage by the power company.
Sag/dip: a short period of low voltage
POWER EXCESS
Surge: Prolonged rise in voltage
Spike: Momentary High Voltage
In-rush current: the initial surge of current required by a load before it reaches normal operation.
- Transient: line noise or disturbance is superimposed on the supply circuit and can cause fluctuations in electrical power
Refence(s) used for this question:
Harris, Shon (2012-10-25). CISSP All-in-One Exam Guide, 6th Edition (p. 462). McGraw-Hill. Kindle Edition.

A series of the same control, hexidecimal, characters imbedded in the string is usually an indicator of a buffer overflow attack. A NOP is a instruction which does nothing (No Operation - the hexadecimal equivalent is 0x90)
The following answers are incorrect:
A syn scan. This is incorrect because a SYN scan is when a SYN packet is sent to a specific port and the results are then analyzed.
A half-port scan. This is incorrect because the port scanner generates a SYN packet. If the target port is open, it will respond with a SYN-ACK packet. The scanner host responds with a RST packet, closing the connection before the handshake is completed. Also known as a Half Open Port scan.
A packet destined for the network's broadcast address. This is incorrect because this type of packet would not contain a long string of NOP characters.

Explanation/Reference:
The structured walk-through test occurs when the functional representatives meet to review the plan in detail. This involves a thorough look at each of the plan steps, and the procedures that are invoked at that point in the plan. This ensures that the actual planned activities are accurately described in the plan. The checklist test is a method of testing the plan by distributing copies to each of the functional areas. The simulation test plays out different scenarios. The parallel test is essentially an operational test that is performed without interrupting current processing.
Source: HARE, Chris, CISSP Study Guide: Business Continuity Planning Domain,

Explanation/Reference:
Controls provide accountability for individuals accessing information. Assurance procedures ensure that access control mechanisms correctly implement the security policy for the entire life cycle of an information system.
Source: KRUTZ, Ronald L. & VINES, Russel D., The CISSP Prep Guide: Mastering the Ten Domains of Computer Security, John Wiley & Sons, 2001, Chapter 2: Access control systems (page 33).

Section: Access Control
Explanation/Reference:
The Bell-LaPadula model focuses on data confidentiality and access to classified information, in contrast to the Biba Integrity Model which describes rules for the protection of data integrity.
In this formal model, the entities in an information system are divided into subjects and objects.
The notion of a "secure state" is defined, and it is proven that each state transition preserves security by moving from secure state to secure state, thereby proving that the system satisfies the security objectives of the model.
The Bell-LaPadula model is built on the concept of a state machine with a set of allowable states in a system.
The transition from one state to another state is defined by transition functions.
A system state is defined to be "secure" if the only permitted access modes of subjects to objects are in accordance with a security policy.
To determine whether a specific access mode is allowed, the clearance of a subject is compared to the classification of the object (more precisely, to the combination of classification and set of compartments, making up the security level) to determine if the subject is authorized for the specific access mode.
The clearance/classification scheme is expressed in terms of a lattice. The model defines two mandatory access control (MAC) rules and one discretionary access control (DAC) rule with three security properties:
The Simple Security Property - a subject at a given security level may not read an object at a higher security level (no read-up).
The property (read "star"-property) - a subject at a given security level must not write to any object at a lower security level (no write-down). The property is also known as the Confinement property.
The Discretionary Security Property - use an access control matrix to specify the discretionary access control.
The transfer of information from a high-sensitivity document to a lower-sensitivity document may happen in the Bell-LaPadula model via the concept of trusted subjects. Trusted Subjects are not restricted by the property.
Untrusted subjects are.
Trusted Subjects must be shown to be trustworthy with regard to the security policy. This security model is directed toward access control and is characterized by the phrase: "no read up, no write down." Compare the Biba model, the Clark-Wilson model and the Chinese Wall.
With Bell-LaPadula, users can create content only at or above their own security level (i.e. secret researchers can create secret or top-secret files but may not create public files; no write-down). Conversely, users can view content only at or below their own security level (i.e. secret researchers can view public or secret files, but may not view top-secret files; no read-up).
Strong Property
The Strong Property is an alternative to the Property in which subjects may write to objects with only a matching security level. Thus, the write-up operation permitted in the usual Property is not present, only a write- to-same level operation. The Strong Property is usually discussed in the context of multilevel database management systems and is motivated by integrity concerns.
Tranquility principle
The tranquility principle of the Bell-LaPadula model states that the classification of a subject or object does not change while it is being referenced. There are two forms to the tranquility principle: the "principle of strong tranquility" states that security levels do not change during the normal operation of the system and the
"principle of weak tranquility" states that security levels do not change in a way that violates the rules of a given security policy.
Another interpretation of the tranquility principles is that they both apply only to the period of time during which an operation involving an object or subject is occurring. That is, the strong tranquility principle means that an object's security level/label will not change during an operation (such as read or write); the weak tranquility principle means that an object's security level/label may change in a way that does not violate the security policy during an operation.
Reference(s) used for this question:
http://en.wikipedia.org/wiki/Biba_Model
http://en.wikipedia.org/wiki/Mandatory_access_control
http://en.wikipedia.org/wiki/Discretionary_access_control
http://en.wikipedia.org/wiki/Clark-Wilson_model
http://en.wikipedia.org/wiki/Brewer_and_Nash_model