Online Access Free Juniper.JN0-363.v2024-07-06.q174 Practice Test (Page 20)

JN0-363 Exam Question 91

Exhibit

Referring to the exhibit, internal BGP between R1 and R2 is not establishing.
What is the problem In this scenario?

A.R1 does not have a route to 192.168.200.2.

B.R1 needs to be configured with a next-hop self policy.

C.R1 needs to be configured with an explicit router ID.

D.R1 and R2 must each have unique AS numbers.

JN0-363 Exam Question 92

Click the Exhibit button. From the output shown in the exhibit, what would happen to a packet destined for address 172.29.3.5?

A.The address is in the aggregate range; the packet will be silently dropped.

B.The address is not in the aggregate range; the packet is sent to the Routing Engine.

C.The address is not in the aggregate range; the packet will be forwarded.

D.The address is in the aggregate range; the packet will be dropped.

JN0-363 Exam Question 93

You are asked to design a Layer 2 VPN service between service provider networks that needs Ethernet transport capabilities. The VPN should support two or three endpoints. Which Layer 2 VPN technology should you propose?

A.BGP-signaled VPLS, using the RFC 4448 Layer 2 frame format

B.LDP-signaled VPLS

C.BGP Layer 2 VPN

D.LDP Layer 2 circuit, using the RFC 4448 Layer 2 frame format

JN0-363 Exam Question 94

You are bringing a new network online with three MX Series devices enabled for STP. No root bridge priority has been configured. Which statement is true in this scenario?

A.The device with the lowest MAC address will be elected as the root bridge.

B.The device with the highest MAC address will be elected as the root bridge.

C.The device with the lowest numerical lo0 IP address will be elected as the root bridge.

D.The device with the highest numerical lo0 IP address will be elected as The bridge.

JN0-363 Exam Question 95

Exhibit

You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit.
What is the problem in this scenario?

A.The family iso statement must be added to the logical interface.

B.The router at the other end of the link Is not sending any IS-IS Hello messages.

C.This is a Gigabit Ethernet interface, that is incompatible with the reference-bandwidth 100g statement.

D.The router at the other end of the link is a Level 1 only router.

Other Version: 915Juniper.JN0-363.v2024-01-10.q118; 1826Juniper.JN0-363.v2023-04-07.q126

Latest Upload: 133VMware.3V0-21.25.v2026-06-20.q29; 134Microsoft.AB-731.v2026-06-19.q23; 271IIA.IIA-CIA-Part2.v2026-06-19.q308; 165DAMA.MD-1220.v2026-06-19.q66; 160ISTQB.CT-AI.v2026-06-18.q68; 253IIA.IIA-CIA-Part3.v2026-06-17.q220; 173WGU.Introduction-to-IT.v2026-06-17.q67; 252CompTIA.220-1202.v2026-06-16.q110; 146TheInstitutes.CPCU-500.v2026-06-16.q25; 234ACAMS.CAMS7-CN.v2026-06-16.q170

JN0-363 Exam Question 91

JN0-363 Exam Question 92

JN0-363 Exam Question 93

JN0-363 Exam Question 94

JN0-363 Exam Question 95

Download PDF File