Online Access Free Nokia.4A0-C01.v2022-03-10.q310 Practice Test (Page 30)

4A0-C01 Exam Question 141

A router is configured with the command "configure router ecmp 4". There are two best paths to a given destination with an equal cost in the IGP.
Which of the following best describes the handling of traffic to this destination?

A.The router installs four routes for the destination with four different next hops. Traffic is evenly distributed over the four paths.

B.The router installs two routes for the destination with two different next hops. A hashing algorithm is used to distribute traffic over the two paths.

C.The router installs four routes for the destination with four different next hops. A hashing algorithm is used to distribute traffic over the four paths.

D.The router installs two routes for the destination with two different next hops. Traffic is evenly distributed over the two paths.

E.The router installs one route for the destination. Traffic is evenly distributed over the two paths.

4A0-C01 Exam Question 142

When configuring RSVP-TE for transport tunnels, which command enables RSVP by default?

A.configure router transport-tunnel

B.configure router rsvp-te

C.configure router mpls

D.configure router tunnel

E.configure router gre

4A0-C01 Exam Question 143

Which of the following about the VPRN data plane is TRUE?

A.The service label is popped by the remote CE.

B.A packet has its service label swapped at each P router.

C.A packet receives a service label and a transport label at the ingress PE.

D.The egress PE pops the service label, and the transport label is forwarded.

4A0-C01 Exam Question 144

Which of the following describes how a router sets the destination IP address for an RSVP RESV message?

A.It sets the address to the system address of the head-end router.

B.It sets the address to the next upstream hop from the RRO.

C.It sets the address to the next upstream hop from the ERO.

D.It sets the address to the next upstream hop from the PSB.

4A0-C01 Exam Question 145

Which of the following best describes how the path-mlu is chosen for an SDP?

A.The path-mtu is signaled between the PE endpoints when the service is established.

B.An SDP does not have a path-mtu

C.The path-mtu is calculated based on the service MTU of the service using the SDP.

D.The path-mtu must be set by the administrator.

E.By default, the path-mtu is calculated automatically from the network port MTU of the PE router.

Other Version: 63Nokia.Itexamdownload.4A0-C01.v2022-04-20.by.morton.310q.pdf; 2863Nokia.4A0-C01.v2021-09-24.q123; 76Nokia.Test4sure.4A0-C01.v2021-09-11.by.christine.272q.pdf

Latest Upload: 124ISTQB.CT-AI.v2026-06-18.q68; 234IIA.IIA-CIA-Part3.v2026-06-17.q220; 161WGU.Introduction-to-IT.v2026-06-17.q67; 200CompTIA.220-1202.v2026-06-16.q110; 133TheInstitutes.CPCU-500.v2026-06-16.q25; 215ACAMS.CAMS7-CN.v2026-06-16.q170; 248CBIC.CIC.v2026-06-15.q123; 149Peoplecert.ITIL-4-Specialist-High-velocity-IT.v2026-06-15.q16; 257HashiCorp.Terraform-Associate-004.v2026-06-15.q126; 156Peoplecert.ITILFNDv5.v2026-06-15.q26

4A0-C01 Exam Question 141

4A0-C01 Exam Question 142

4A0-C01 Exam Question 143

4A0-C01 Exam Question 144

4A0-C01 Exam Question 145

Download PDF File