In the 802.11 wireless networking protocols, when a client station sends a broadcast probe request frame with a wildcard SSID (Service Set Identifier), it is essentially asking for any nearby access points (APs) to identify themselves. The way APs respond to such a probe request is governed by standard 802.11 behavior, which includes:
* Probe Request Handling: Upon receiving a broadcast probe request, each AP that can serve the client prepares a probe response. The response includes information about the AP, such as its SSID, supported data rates, and other capabilities.
* Contention-Based Mechanism: Wireless networks use a contention-based mechanism (CSMA/CA - Carrier Sense Multiple Access with Collision Avoidance) for medium access. Each AP must wait for a clear channel and win the contention process before it can send its probe response.
* Independent Responses: Each AP operates independently in responding to the probe request. There is no coordination between APs to decide which one responds first or at all, leading to multiple APs sending probe responses, each after winning the contention for the medium.
Option A accurately reflects this process, indicating that each AP prepares and sends a probe response in turn, contingent upon winning the medium contention. The other options suggest mechanisms (such as coordination with a DHCP server or simultaneous responses after a Short Interframe Space (SIFS)) that do not align with standard 802.11 procedures for handling broadcast probe requests.
References:
* IEEE 802.11 Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications.
* CWNA Certified Wireless Network Administrator Official Study Guide: Exam PW0-105, by David D.
Coleman and David A. Westcott.

The data rate of a signal is the speed that the data bits in individual 802.11 data frames are sent, but it does not account for the actual amount of data that can be transmitted over time. The throughput of a connection is the flow of information over time, which is affected by various factors such as data encoding, modulation, encryption, airtime utilization, noise levels, interference, etc. Therefore, the throughput is always lower than the data rate. According to one of the web search results1, the actual throughput is normally 60-70 percent of the supported data rates. So, for a connection with a data rate of 150 Mbps, the expected throughput would be around 90-105 Mbps.

Weak signal strength is the likely cause of the low data rate issue for the client that has a signal strength of -84 dBm and a noise floor of -96 dBm. The client is an 802.11ac client and connects to an 802.11ac AP. Both the client and AP are 2x2:2 devices. Signal strength is the measure of how strong the RF signal is at the receiver.
Signal strength can affect the reliability and performance of the wireless connection, as well as the data rate and throughput of the traffic. The higher the signal strength, the better the signal quality and the higher the data rate. The lower the signal strength, the worse the signal quality and the lower the data rate.
The data rate of an 802.11ac connection depends on several factors, such as channel bandwidth, modulation and coding scheme (MCS), spatial streams, guard interval, and beamforming. However, these factors are also influenced by the signal strength, as they require a certain signal-to-noise ratio (SNR) to operate properly.
SNR is the ratio of the signal strength to the noise floor, which is the measure of the background noise or interference in the RF environment. The higher the SNR, the more robust and efficient the communication.
The lower the SNR, the more prone and vulnerable to errors and retries.
According to the CWNA Official Study Guide , Table 3.7, page 112, an 802.11ac connection with a channel bandwidth of 80 MHz, an MCS of 9, two spatial streams, a short guard interval, and no beamforming can achieve a maximum data rate of 867 Mbps. However, this data rate requires a minimum SNR of 30 dB to maintain a sufficient signal quality. If the signal strength is -84 dBm and the noise floor is -96 dBm, then the SNR is only 12 dB (-84 dBm - (-96 dBm) = 12 dB), which is far below the required SNR for this data rate.
Therefore, the data rate will drop significantly to match the lower SNR and signal quality.
To solve this problem, the signal strength should be increased to improve the SNR and data rate. This can be done by adjusting the output power or channel assignment of the AP or client, relocating or reorienting some APs or antennas to reduce attenuation or interference, updating or replacing some faulty oroutdated hardware or software components, etc. References: , Chapter 3, page 112; , Section 3.2

The beamwidth of an RF antenna is the angular measure of how wide the main lobe of radiation is. The main lobe is the area where the signal strength is highest and most concentrated. The beamwidth is calculated at the points where the main lobe decreases power by 3 dB, which means it is half of the maximum power. The beamwidth can be measured in both horizontal and vertical planes, depending on how the antenna is oriented.
The horizontal beamwidth is also called azimuth, while the vertical beamwidth is also called elevation. The beamwidth patterns on an antenna polar chart indicate how the RF energy is distributed in different directions. References: 1, Chapter 2, page 66; 2, Section 2.3

Elevators are a common building item that frequently causes RF shadow and must be accounted for in coverage plans. RF shadow is a term that describes an area where wireless signals are blocked or significantly weakened by an obstacle or an object that absorbs or reflects RF energy. RF shadow can cause lack of coverage or poor performance in a WLAN because wireless devices in those areas may not be able to communicate with access points or other devices. RF shadow can be mitigated by adjusting access point placement, antenna orientation, transmit power level, or channel selection to avoid or overcome the obstacle or object that causes it. Elevators are a common building item that frequently causes RF shadow because they are made of metal and they move up and down within a shaft. Metal is a material that has high attenuation and reflection values, which means it can block or bounce off wireless signals very effectively. A moving elevator can create dynamic RF shadow that changes depending on its position and direction. Therefore, elevators must be accounted for in coverage plans to ensure adequate WLAN coverage and performance throughout the facility. The other options are not common building items that frequently cause RF shadow or must be accounted for in coverage plans. Wooden doors are not likely to cause RF shadow because they are made of wood, which is a material that has low attenuation and reflection values, which means it can pass through or slightly weaken wireless signals. Carpeted floors are not likely to cause RF shadow because they are made of fabric, which is a material that has low attenuation and reflection values, which means it can pass through or slightly weaken wireless signals. Cubicle partitions are not likely to cause RF shadow because they are made of thin plastic or cardboard, which are materials that have low attenuation and reflection values, which means they can pass through or slightly weaken wireless signals. References: CWNA-109 Study Guide, Chapter 13:
Wireless LAN Site Surveys - Types & Processes , page 433