Online Access Free Cisco.300-410.v2021-10-09.q161 Practice Test (Page 33)

300-410 Exam Question 156

Refer to the exhibit.

Redistribution is enabled between the routing protocols, and nowPC2 PC3, and PC4 cannot reach PC1. What are the two solutions to fix the problem? (Choose two.)

A.Filter RIP routes back into RIP when redistributing into RIP in R2

B.Filter OSPF routes into RIP FROM EIGRP when redistributing into RIP in R2.

C.Filter all routes except RIP routes when redistributing into EIGRP in R2.

D.Filter RIP AND OSPF routes back into OSPF from EIGRP when redistributing into OSPF in R2

E.Filter all routes except EIGRP routes when redistributing into OSPF in R3.

300-410 Exam Question 157

Refer to the exhibit.

An engineer identifier a Layer 2 loop using DNAC. Which command fixes the problem in the SF-D9300-1 switch?

A.no spanning-tree uplinkfast

B.spanning-tree loopguard default

C.spanning-tree backbonesfast

D.spanning-tree portfast bpduguard

300-410 Exam Question 158

What is a prerequisite for configuring BFD?

A.Cisco Express Forwarding must be enabled on all participating BFD endpoints.

B.To use BFD with BGP. the timers 3 9 command must first be configured in the BGP routing process.

C.All routers in the path between two BFD endpoints must have BFD enabled.

D.Jumbo frame support must be configured on the router that is using BFD.

300-410 Exam Question 159

Refer to the exhibit.

R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to
172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?

A.R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.

B.In route reflector setup, only classful prefixes are advertised to other clients.

C.In route reflector setups, prefixes are not advertised from one client to another.

D.Route reflector setup requires full IBGP mesh between the routers.

300-410 Exam Question 160

Refer to the exhibit.

Which interface configuration must be configured on the HUB router to enable MVPN with mGRE mode?

A.Option A

B.Option B

C.Option C

D.Option D

Other Version: 1156Cisco.300-410.v2026-02-04.q370; 1946Cisco.300-410.v2024-01-03.q227; 2133Cisco.300-410.v2023-02-14.q151; 4404Cisco.300-410.v2022-08-13.q115; 2750Cisco.300-410.v2022-08-11.q99; 3202Cisco.300-410.v2022-07-18.q102; 4929Cisco.300-410.v2022-07-02.q117; 2420Cisco.300-410.v2022-06-24.q106; 66Cisco.Real4prep.300-410.v2022-06-08.by.lisa.285q.pdf; 7023Cisco.300-410.v2022-02-25.q285; 91Cisco.Itpass4sure.300-410.v2021-09-03.by.afra.234q.pdf

Latest Upload: 106F5.F5CAB5.v2026-06-22.q29; 112Juniper.JN0-650.v2026-06-22.q31; 126Salesforce.Plat-Admn-201.v2026-06-22.q72; 152VMware.3V0-21.25.v2026-06-20.q29; 149Microsoft.AB-731.v2026-06-19.q23; 289IIA.IIA-CIA-Part2.v2026-06-19.q308; 170DAMA.MD-1220.v2026-06-19.q66; 175ISTQB.CT-AI.v2026-06-18.q68; 316IIA.IIA-CIA-Part3.v2026-06-17.q220; 216WGU.Introduction-to-IT.v2026-06-17.q67

300-410 Exam Question 156

300-410 Exam Question 157

300-410 Exam Question 158

300-410 Exam Question 159

300-410 Exam Question 160

Download PDF File