The selected resolution is Modify the FCoE VLAN because the failure is in the Fibre Channel/FCoE control path around FCoE. Cisco MDS and Nexus platforms separate configuration from operational state: a VSAN, zone, vFC binding, device alias, or port-security entry can exist in configuration but still fail if it is not active, correctly merged, or allowed on the link. The correct option addresses the fabric condition that prevents communication. The incorrect options are technically adjacent but would not repair the specific dependency; for example, changing unrelated databases or resetting ports without correcting policy leaves the same failure to recur. Cisco SAN troubleshooting therefore starts with port role and VSAN checks, then confirms fabric services such as fcdomain, FSPF, zoning, fabric binding, and name-server information. The expected validation is that the port becomes operational, the initiator and target appear in the appropriate databases, and permitted zone members can communicate.

The correct remediation is A Cisco APIC must be attached to leaf nodes; Leaf nodes must connect to spine nodes only. In Cisco data center troubleshooting, the first priority is to isolate whether the failure is caused by the underlay, overlay control plane, first-hop gateway behavior, or a consistency parameter. This item is centered on APIC, so the selected action targets the condition that prevents normal forwarding rather than masking the symptom. Cisco Nexus and ACI guidance treats vPC, VXLAN EVPN, OTV, OSPF, BGP, HSRP, and LACP issues as state-dependent technologies: a neighbor, peer, VLAN, VNI, multicast group, timer, MTU, or policy mismatch can leave the protocol partially operational while traffic is still dropped. The rejected alternatives either change unrelated attributes, introduce a new inconsistency, or affect only a secondary behavior. The operational check after applying the fix should be to confirm adjacency or peer state, validate the relevant route/MAC/endpoint table, and test traffic in the affected VLAN or VRF. This aligns with Cisco DCIT network troubleshooting methodology for isolating control-plane state before changing data- plane policy.

The correct answer is shell:domains=Security_Domain_1/Read_Role_1|Read_Role_2. Cisco management and operations troubleshooting focuses on control-plane services such as RBAC, AAA, certificates, SNMP, firmware packages, centralized management registration, fault workflows, and node lifecycle state. This item references the affected data-center component, so the selected action fixes the management dependency rather than the data-plane symptom. Cisco platforms often allow basic reachability while a higher-level integration still fails because of time synchronization, certificate trust, role mapping, authorization attributes, feature state, or incomplete lifecycle cleanup. The other options either modify forwarding behavior, adjust the wrong credential or role, or bypass the required operational workflow. The engineer should validate the fix by confirming the management session or registration, checking the relevant fault or audit log, and confirming that the user, node, or integration has the expected role and operational status. This is consistent with Cisco DCIT emphasis on operational evidence before and after the change.

Enable the peer-gateway feature is correct because the failure is an operations-plane condition involving HSRP. In Cisco data center products, management functions depend on more than IP connectivity. AAA servers must return the correct attributes, RBAC must map users to the correct security domain or role, certificates must be trusted and valid for the access method, and firmware or registration workflows must satisfy documented prerequisites such as NTP and required ports. The selected answer corrects that dependency. The distractors are not root-cause fixes because they either target a different subsystem or change a setting that would not influence the observed login, registration, warning, or fault. After the change, validation should include a successful login or registration test, review of the audit/fault record, and confirmation that the expected administrative scope is enforced. That approach matches Cisco operational troubleshooting for DCIT environments. The final check is to document the before-and-after state so the remediation is tied to a repeatable Cisco troubleshooting symptom rather than an assumed fix.

The correct answer is Configure the hello timer to match the neighbor. Cisco MDS and Nexus SAN troubleshooting is driven by fabric state: the host and target must be in the correct VSAN, must complete FLOGI/PLOGI where applicable, and must be permitted by active zoning, fcdomain, FSPF, NPV/NPIV, or port-security policy. This question focuses on VSAN, FSPF, so the selected action fixes the dependency that prevents the initiator, target, or inter-switch link from becoming usable. Cisco documentation emphasizes checking VSAN membership, active zonesets, correct port mode, fabric binding, device-alias consistency, and the relevant FC databases before changing unrelated server settings. The distractors either target a different database, use the wrong port role, or would not cause the observed Fibre Channel state to change. After the fix, the engineer should confirm the interface state, FLOGI database, name-server entries, zoneset activation, and successful initiator-to-target reachability with tools such as fcping or fabric show commands.