The selected resolution is FCoE license; F-Series module because the failure is in the Fibre Channel/FCoE control path around FCoE. Cisco MDS and Nexus platforms separate configuration from operational state: a VSAN, zone, vFC binding, device alias, or port-security entry can exist in configuration but still fail if it is not active, correctly merged, or allowed on the link. The correct option addresses the fabric condition that prevents communication. The incorrect options are technically adjacent but would not repair the specific dependency; for example, changing unrelated databases or resetting ports without correcting policy leaves the same failure to recur. Cisco SAN troubleshooting therefore starts with port role and VSAN checks, then confirms fabric services such as fcdomain, FSPF, zoning, fabric binding, and name-server information. The expected validation is that the port becomes operational, the initiator and target appear in the appropriate databases, and permitted zone members can communicate.

Add the DNS server and suffix; Configure domain-name and nameserver under the management VRF resolves the problem because the symptom is specific to the automation subsystem handling Guest Shell, Cisco Nexus, Nexus 9000, Cisco Nexus 9000. Nexus automation failures are frequently caused by a missing EEM event statement, absent event-default action, invalid REST path, incorrect JSON or XML syntax, Guest Shell DNS/resource settings, or a scheduler feature that is not enabled. The selected answer corrects that execution prerequisite. The wrong options may make sense for normal switch forwarding, but they do not repair the automation control path. Cisco documentation treats Guest Shell as a separate Linux environment and EEM as a policy engine that can intercept CLI events; both must be validated from their own operational state. A proper verification is to confirm the policy is registered, run the job or API call again, review the response or syslog output, and ensure that normal CLI behavior is preserved after the automation fires.

The correct action is interface ethernet 1/25 switchport port-security maximum 1 switchport port-security mac- address bbbb.cccc.dd11. Cisco UCS troubleshooting depends on the relationship between policy, inventory discovery, firmware state, and server identity. The question involves UCS, Cisco Nexus, so the selected option fixes the UCS component or policy that directly controls the failure. In UCS Manager, service profiles, vNIC/vHBA templates, boot policies, firmware packages, server pools, adapters, fabric interconnects, and I/O modules are applied through a managed model; a server can fail even when basic IP reachability exists if the relevant policy is incomplete or the hardware inventory has not been acknowledged correctly. The distractors typically change an unrelated object, force a disruptive recovery without fixing the policy, or apply to a different UCS mode. Cisco guidance is to verify faults, FSM stage, inventory status, association status, and the specific boot or connectivity policy before taking action. After the remediation, validate that the fault clears, the FSM completes, and the server or fabric component returns to the expected operable state.

The correct answer is Enable LLDP on the neighbor switch. Cisco MDS and Nexus SAN troubleshooting is driven by fabric state: the host and target must be in the correct VSAN, must complete FLOGI/PLOGI where applicable, and must be permitted by active zoning, fcdomain, FSPF, NPV/NPIV, or port-security policy. This question focuses on VSAN, FCoE, DCBX, LLDP, so the selected action fixes the dependency that prevents the initiator, target, or inter-switch link from becoming usable. Cisco documentation emphasizes checking VSAN membership, active zonesets, correct port mode, fabric binding, device-alias consistency, and the relevant FC databases before changing unrelated server settings. The distractors either target a different database, use the wrong port role, or would not cause the observed Fibre Channel state to change. After the fix, the engineer should confirm the interface state, FLOGI database, name-server entries, zoneset activation, and successful initiator-to-target reachability with tools such as fcping or fabric show commands.

Install Infrastructure Firmware, then Install Server Firmware is correct because the failure is tied to the UCS managed state of UCS, firmware, Auto Install. In Cisco UCS, policies are not advisory; they are the source from which fabric interconnects program adapters, boot targets, server identity, firmware, and external integrations. A mismatch between the policy and the actual hardware or upstream storage/network state can cause boot, discovery, KVM, firmware, or connectivity failures. The selected action addresses the object that UCS Manager uses to build the final operational configuration. The distractors either solve a different fault domain or bypass the policy model. A disciplined DCIT validation sequence is to check the fault code, the FSM history, the equipment inventory, the service profile association, and the relevant adapter or boot table.
If those states are correct after the change, the UCS component should return to operable service without unnecessary reconfiguration.