Coaxial cable is a type of cable that consists of a central copper conductor surrounded by an insulating layer and a braided metal shield. Coaxial cable is commonly used to connect a cable modem to an ISP by transmitting data over cable television networks. Coaxial cable can support high bandwidth and long distances with minimal interference or attenuation. Reference: https://partners.comptia.org/docs/default-source/resources/comptia-network-n10-008-exam-objectives-(2-0), https://www.techopedia.com/definition/4027/coaxial-cable

The most likely cause of the intermittent connectivity issues when specific Wireless Access Points (WAPs) are turned on and share channel five is interference. Wireless interference occurs when multiple devices operate on the same channel within close proximity to each other, leading to signal congestion and reduced performance. This type of interference can cause the connectivity to be sporadic, as described. Other options like polarization, incorrect channel (since they are on the intended channel), or low power levels would generally not cause intermittent issues strictly when WAPs are turned on.

See the answer and solution below in Explanation
Explanation:
Network Health:
WAN 2 appears to have a lower average latency and loss percentage, which would make it the preferred WAN station for VoIP traffic. VoIP traffic requires low latency and packet loss to ensure good voice quality and reliability. WAN 1 seems to have higher RAM and processor usage, which could also affect the performance of VoIP traffic.
Here's the summary of the key metrics for WAN 1 and WAN 2 from the image provided:
WAN 1:
Uplink Speed: 10G
Total Usage: 26.969GB Up / 1.748GB Down
Average Throughput: 353MBps Up / 23.42MBps Down
Loss: 2.51%
Average Latency: 24ms
Jitter: 9.5ms
WAN 2:
Uplink Speed: 1G
Total Usage: 930GB Up / 138GB Down
Average Throughput: 12.21MBps Up / 1.82MBps Down
Loss: 0.01%
Average Latency: 11ms
Jitter: 3.9ms
For VoIP traffic, low latency and jitter are particularly important to ensure voice quality. While WAN 1 has higher bandwidth and throughput, it also has higher latency and jitter compared to WAN 2. However, WAN 2 has much lower loss, lower latency, and lower jitter, which are more favorable for VoIP traffic that is sensitive to delays and variation in packet arrival times.
Given this information, WAN 2 would generally be preferred for VoIP traffic due to its lower latency, lower jitter, and significantly lower loss percentage, despite its lower bandwidth compared to WAN 1. The high bandwidth of WAN 1 may be more suitable for other types of traffic that are less sensitive to latency and jitter, such as bulk data transfers.

Device Monitoring:
the device that is experiencing connectivity issues is the APP Server or Router 1, which has a status of Down. This means that the server is not responding to network requests or sending any dat a. You may want to check the physical connection, power supply, and configuration of the APP Server to troubleshoot the problem.

QSFP+ is a type of transceiver that supports 40 gigabit Ethernet (40GbE) over four lanes of 10 gigabit Ethernet (10GbE) each. QSFP+ stands for quad small form-factor pluggable plus, and it is a compact and hot-swappable module that plugs into a QSFP+ port on a network device. QSFP+ transceivers can support various types of cables and connectors, such as direct attach copper (DAC), active optical cable (AOC), or fiber optic cable.
Multimode is a type of fiber optic cable that supports multiple modes of light propagation within the core. Multimode fiber optic cable can carry higher bandwidth and data rates than single-mode fiber optic cable, but over shorter distances. Multimode fiber optic cable is commonly used for short-reach applications, such as within a data center or a campus network. Multimode fiber optic cable can be paired with QSFP+ transceivers to achieve 40GbE connectivity.
The other options are not correct because they do not support 40GbE. They are:
SFP+. SFP+ is a type of transceiver that supports 10 gigabit Ethernet (10GbE) over a single lane. SFP+ stands for small form-factor pluggable plus, and it is a compact and hot-swappable module that plugs into an SFP+ port on a network device. SFP+ transceivers can support various types of cables and connectors, such as direct attach copper (DAC), active optical cable (AOC), or fiber optic cable. However, SFP+ transceivers cannot support 40GbE by themselves, unless they are used in a breakout configuration with a QSFP+ transceiver.
SFP. SFP is a type of transceiver that supports 1 gigabit Ethernet (1GbE) over a single lane. SFP stands for small form-factor pluggable, and it is a compact and hot-swappable module that plugs into an SFP port on a network device. SFP transceivers can support various types of cables and connectors, such as twisted-pair copper, coaxial cable, or fiber optic cable. However, SFP transceivers cannot support 40GbE by themselves, unless they are used in a breakout configuration with a QSFP+ transceiver.
Cat 6a. Cat 6a is a type of twisted-pair copper cable that supports 10 gigabit Ethernet (10GbE) over distances up to 100 meters. Cat 6a stands for category 6 augmented, and it is an enhanced version of Cat 6 cable that offers better performance and reduced crosstalk. Cat 6a cable can be paired with 10Gbase-T transceivers to achieve 10GbE connectivity. However, Cat 6a cable cannot support 40GbE by itself, unless it is used in a breakout configuration with a QSFP+ transceiver.
Cat 5e. Cat 5e is a type of twisted-pair copper cable that supports 1 gigabit Ethernet (1GbE) over distances up to 100 meters. Cat 5e stands for category 5 enhanced, and it is an improved version of Cat 5 cable that offers better performance and reduced crosstalk. Cat 5e cable can be paired with 1000base-T transceivers to achieve 1GbE connectivity. However, Cat 5e cable cannot support 40GbE by itself, unless it is used in a breakout configuration with a QSFP+ transceiver.
Reference
1: QSFP+ - an overview | ScienceDirect Topics
2: Multimode Fiber - an overview | ScienceDirect Topics
3: Network+ (Plus) Certification | CompTIA IT Certifications
4: SFP+ - an overview | ScienceDirect Topics
5: SFP - an overview | ScienceDirect Topics
6: Cat 6a - an overview | ScienceDirect Topics
7: [Cat 5e - an overview | ScienceDirect Topics]

Giants are packets that exceed the configured MTU (Maximum Transmission Unit) of a switchport or interface, which causes them to be dropped or fragmented by the switch or router. The MTU is the maximum size of a packet that can be transmitted without fragmentation on a given medium or protocol. Giants can indicate misconfiguration or mismatch of MTU values between devices or interfaces on a network, which can cause performance issues or errors. CRC errors are errors that occur when the cyclic redundancy check (CRC) value of a packet does not match the calculated CRC value at the destination, which indicates corruption or alteration of data during transmission due to noise, interference, faulty cabling, etc., but not necessarily exceeding MTU values. Runts are packets that are smaller than the minimum size allowed by the medium or protocol, which causes them to be dropped or ignored by the switch or router. Flooding is a technique where a switch sends packets to all ports except the source port when it does not have an entry for the destination MAC address in its MAC address table, which can cause congestion or broadcast storms on a network.