Online Access Free D-PDC-DY-23 Exam Questions

A network administrator must configure a virtual IP address using VRRP on interface VLAN 100 within OS10.
What are the correct steps to accomplish this?

• A.OS10(config)# interface vlan 100
  OS10(conf-if-vl-100)# ip address 10.0.100.2/24
  OS10(conf-if-vl-100)# standby-group 250
  OS10(conf-vlan100-vrid-250)# virtual-address 10.0.100.1
• B.OS10(config)# interface vlan 100
  OS10(conf-if-vl-100)# ip address 10.0.100.1/24
  OS10(conf-if-vl-100)# standby-group 256
  OS10(conf-vlan100-vrid-256)# standby-address 10.0.100.2
• C.OS10(config)# interface vlan 100
  OS10(conf-if-vl-100)# ip address 10.0.100.2/24
  OS10(conf-if-vl-100)# vrrp-group 256
  OS10(conf-vlan100-vrid-256)# virtual-address 10.0.100.1
• D.OS10(config)# interface vlan 100
  OS10(conf-if-vl-100)# ip address 10.0.100.1/24
  OS10(conf-if-vl-100)# vrrp-group 250
  OS10(conf-vlan100-vrid-250)# virtual-address 10.0.100.2

What are the correct steps to configure a static LAG on a Dell Networking OS10 switch?

• A.interface port-channel 4 no shutdown interface range ethernet 1/1/14-1/1/15 channel-group 4 mode on
• B.interface port-channel 4 no shutdown interface range ethernet 1/1/14-1/1/15 channel-group 4 mode active
• C.interface port-channel 4 channel-group 4 mode passive interface range ethernet 1/1/14-1/1/15 channel-group 4 mode on
• D.interface port-channel 4 channel-group 4 mode on interface range ethernet 1/1/14-1/1/15 channel- group 4 mode passive

Which two options describe differences between Layer 2 and Layer 3 QoS? (Select 2)

• A.802.1P trust-maps only function on untagged VLANs.
• B.Class of Service priorities are encoded in the 802.1Q header.
• C.IP Precedence implements 64 unique traffic classes for packet queueing.
• D.DSCP uses the same Type of Service Field that IP Precedence uses.

Refer to the exhibit:

From S1, a ping to the host address of 192.168.37.3 is not successful. The routing table on S1 shows three directly connected networks (including the Lo0 network of S1). Network 192.168.34.0/24 and the Lo0 networks of S2 and S3 are the only OSPF-learned networks in the routing table. The system on the
192.168.37.0/24 network can ping S3.
Which command offers a solution to the inability to ping the host address from S1?

• A.S3(config-router-ospf-1)# update-source loopback 0
• B.S1(config-router-ospf-1)# ip route 192.168.37.0/24 interface null 0
• C.S1(config-router-ospf-1)# network 192.168.37.0/24
• D.S3(config-router-ospf-1)# redistribute connected

What is the range of values that can be used when using the vlt-port-channel command?

• A.1-256
• B.1-512
• C.1-1024
• D.1-128