Online Access Free Fortinet.NSE6_FSW-7.2.v2025-02-05.q19 Practice Test (Page 3)

NSE6_FSW-7.2 Exam Question 6

How does FortiGate handle configuration of flow tracking sampling if you export the settings to a managed FortiSwitch stack with sampling mode set to perimeter is true?

A.FortiGate configures and enables egress sampling on all management interfaces.

B.FortiGate configures and enables flow sampling on FortiSwitch but does not change existing sampling settings of interfaces.

C.FortiGate configures FortiSwitch to perform ingress sampling on all switch interfaces, except ICL and ISL interfaces.

D.FortiGate configures FortiSwitch to perform ingress sampling on all switch interfaces.

NSE6_FSW-7.2 Exam Question 7

Which interfaces on FortiSwitch send out FortiLink discovery frames by default in order to detect a FortiGate with an enabled FortiLink interface?

A.No ports are enabled by default for auto-discovery. This must be configured under config switch interface.

B.All ports have auto-discovery enabled by default.

C.The last four switch ports on FortiSwitch have auto-discovery enabled by default.

D.The ports with auto-discovery enabled by default are dependent upon the FortiSwitch model.

NSE6_FSW-7.2 Exam Question 8

Which drop policy mode, if assigned to a congested port, will drop incoming packets until there is no congestion on the egress port?

A.Weighted round robin mode.

B.Tail-drop mode

C.Strict mode

D.Random early detection mode

NSE6_FSW-7.2 Exam Question 9

Refer to the exhibit.

The profile shown in the exhibit is assigned to a group of managed FortiSwitch ports, and these ports are connected to endpoints which are powered by PoE.
Which configuration action can you perform on the LLDP profile to cause these endpoints to exchange PoE information and negotiate power with the managed FortiSwitch?

A.Assign a new LLDP profile to handle different LLDP-MED TLVs.

B.Add power management as part of LLDP-MED TLVs to advertise.

C.Define an LLDP-MED location ID to use standard protocols for power.

D.Create new a LLDP-MED application type to define the PoE parameters.

NSE6_FSW-7.2 Exam Question 10

How does FortiSwitch perform actions on ingress and egress traffic using the access control list (ACL)?

A.Classifiers enable matching traffic based only on the VLAN ID.

B.ACL can be used only at the prelookup stage in the traffic processing pipeline.

C.FortiSwitch checks ACL policies only from top to bottom.

D.Only high-end FortiSwitch models support ACL.

Other Version: 677Fortinet.NSE6_FSW-7.2.v2025-08-28.q28; 5894Fortinet.NSE6_FSW-7.2.v2025-05-14.q20

Latest Upload: 125ISTQB.CT-AI.v2026-06-18.q68; 236IIA.IIA-CIA-Part3.v2026-06-17.q220; 163WGU.Introduction-to-IT.v2026-06-17.q67; 202CompTIA.220-1202.v2026-06-16.q110; 135TheInstitutes.CPCU-500.v2026-06-16.q25; 216ACAMS.CAMS7-CN.v2026-06-16.q170; 256CBIC.CIC.v2026-06-15.q123; 152Peoplecert.ITIL-4-Specialist-High-velocity-IT.v2026-06-15.q16; 262HashiCorp.Terraform-Associate-004.v2026-06-15.q126; 158Peoplecert.ITILFNDv5.v2026-06-15.q26

NSE6_FSW-7.2 Exam Question 6

NSE6_FSW-7.2 Exam Question 7

NSE6_FSW-7.2 Exam Question 8

NSE6_FSW-7.2 Exam Question 9

NSE6_FSW-7.2 Exam Question 10

Download PDF File