Online Access Free JN0-692 Exam Questions

Which two statements are true about the OSPF 2-Way state? (Choose two.)

• A.It indicates that a device cannot accept any more full adjacencies.
• B.It is the normal state for two neighbors that are neither the DR nor BDR.
• C.It is the normal state for neighbors that are the DR and BDR.
• D.It indicates that communication between two neighbors is bidirectional.

You have created a new IS-IS adjacency between identical routers over two STM-4 circuits. After enabling no-keepalives on the interfaces, they come up and you are able to ping between the routers. However, the IS-IS adjacency still will not establish.
Which step will determine the cause of the problem?

• A.Disable cisco-hdlc encapsulation, enable ppp encapsulation, commit, and test the circuits.
• B.Disable no-keepalives from the interfaces and issue a show interfaces extensive command for each of the SONET interfaces.
• C.Disable no-keepalives from the interfaces and issue a show isis adjacency command.
• D.Enable family iso on all the SONET interfaces, commit, and test the circuits.

Referring to the exhibit, which statement is true about the multicast state on R3?

• A.R3 has no receivers.
• B.R3 is not receiving any traffic
• C.R3 has no PIM neighbors.
• D.R3 has no route to RP.

Click the Exhibit button.
-- Exhibit -user@PE1# show protocols mpls userel-switched-path LSP-1 {
from 101.101.101.1;
to 103.103.103.1; } userel-switched-path LSP-2 {
from 101.101.101.1;
to 103.103.103.1; } interface ge-0/0/0.0;
user@PE1# show protocols ldp interface lo0.0;
user@PE1# show protocols l2circuit
neighbor 103.103.103.1 { interface ge-0/0/3.300 { virtual-circuit-id 300; }
}
user@PE1# show interfaces ge-0/0/3 flexible-vlan-tagging; encapsulation flexible-ethernet-services;
unit 300 { encapsulation vlan-ccc; vlan-id 300;
}
user@PE1# show protocols l2circuit
neighbor 103.103.103.1 { interface ge-0/0/3.300 { virtual-circuit-id 300; community test-community; }
}
user@PE1# show policy-options community test-community members 300:300; -- Exhibit -
Given the topology shown below: CE1-PE1-P-PE2-CE2
PE1 and PE2 have two equal-cost RSVP LSPs (LSP-1 and LSP-2). They form a Layer 2 circuit between CE1 and CE2. You are asked to map their traffic to take LSP-1. The exhibit shows the current configuration of PE1. The correct configuration has been completed on the other routers.
Which two configurations must be added to PE1 to ensure that this traffic is always carried on LSP-1? (Choose two.)

• A.policy-statement mapping-l2ckt-to-lsp {
  term 1 {
  from community test-community;
  then {
  accept;
  }
  }
  }
  user@PE1# show routing-options
• B.policy-statement mapping-l2ckt-to-lsp {
  term 1 {
  from community test-community;
  then {
  install-nexthop lsp LSP-1;
  }
  }
  }
  user@PE1# show policy-options
• C.forwarding-table {
  import mapping-l2ckt-to-lsp;
  }
  user@PE1# show routing-options
• D.forwarding-table {
  export mapping-l2ckt-to-lsp;
  } user@PE1# show policy-options

You notice that an EBGP peering session has terminated and no NOTIFICATION message appears in the traceoptions output.
What has happened?

• A.The peer state was reset to Idle.
• B.The peer router has crashed.
• C.The peer has restarted the hold timer.
• D.The peer update message was missing essential BGP attributes.