The difference between a Data frame and a QoS-Data frame is that QoS Data frames include a QoS control field. A Data frame is a type of data frame that is used to carry user data or upper layer protocol data between STAs and APs. A QoS Data frame is a type of data frame that is used to carry user data or upper layer protocol data between STAs and APs that support QoS (Quality of Service) features. QoS features allow different types of traffic to be prioritized and handled differently according to their QoS requirements, such as delay, jitter, throughput, etc. QoS Data frames include a QoS control field in their MAC header, which contains information such as traffic identifier (TID), queue size (TXOP), acknowledgment policy (ACK), etc., that are used for QoS purposes. The other options are not correct, as they do not describe the difference between Data and QoS Data frames. QoS Data frames do not include a DSCP (Differentiated Services Code Point) control field, which is part of the IP header in the network layer, not the MAC header in the data link layer. QoS Data frames do not include a QoS information element (IE), which is part of some management frames that indicate QoS capabilities or parameters, not data frames. QoS Data frames do not include an 802.1 Q VLAN tag, which is part of some Ethernet frames that indicate VLAN membership or priority, not wireless frames. References: [Wireless Analysis Professional Study Guide CWAP-405], Chapter 5: 802.11 MAC Sublayer, page 118-119

The device finder is a common feature of a spectrum analyzer that helps locate a non-802.11 interference source. The device finder uses a directional antenna to measure the signal strength of a specific frequency or signal source. By pointing the antenna in different directions, the device finder can indicate the direction and distance of the interference source. The device finder can also filter out other signals that are not related to the interference source. The other options are not correct, as they do not help locate a non-802.11 interference source. Max hold and min hold are features that show the maximum and minimum RF power levels over time, respectively. Location filter is a feature that filters out signals that are not from a specific location or area. References: [Wireless Analysis Professional Study Guide CWAP-405], Chapter 3: Spectrum Analysis, page 77-78

An AIFS is a variable interframe space introduced by 802.11e to help prioritize medium access for different Access Categories (ACs). An interframe space is a period of time that a STA (station) has to wait before attempting to access the medium. An AIFS is a type of interframe space that varies depending on the AC of the traffic. An AC is a logical queue that corresponds to a QoS (Quality of Service) level for different types of traffic. There are four ACs defined by 802.11e: AC_VO (Voice), AC_VI (Video), AC_BE (Best Effort), and AC_BK (Background). Each AC has a different AIFSN (Arbitration Interframe Space Number) value, which determines how long it has to wait before attempting to access the medium. A lower AIFSN value means a higher priority and a shorter waiting time. The other options are not correct, as they do not describe what an AIFS is. An AIFS is not a medium access method introduced by 802.11n, but never implemented, as it is part of the 802.11e standard and widely used in QoS-enabled WLANs. An AIFS is not a form of aggregation performed at the PHY layer based on 802.11e UP values interpreted from DSCP values, as aggregation is a technique that combines multiple frames into one larger frame to improve efficiency and throughput, not prioritization or medium access. An AIFS is not the shortest period of time a STA can sleep, as sleeping is a power saving mode that allows a STA to conserve battery power by periodically turning off its radio, not accessing the medium. References: [Wireless Analysis Professional Study Guide CWAP-405], Chapter 7:
QoS Analysis, page 194-195

A STA that supports 802.11k Radio Measurement would send a Neighbor Request to an AP to request a list of neighboring APs which the STA can use as roaming candidates. A Neighbor Request is an Action frame that contains a subelement specifying the type of information that the STA wants to receive from the AP. A Neighbor Report is an Action frame that contains a subelement with a list of neighboring APs that match the criteria specified in the Neighbor Request. The Neighbor Report provides information such as BSSID, channel, operating class, and PHY type of each neighboring AP. This information helps the STA to perform intelligent roaming decisions based on signal quality, load, and compatibility . References: CWAP-
405Certified Wireless Analysis Professional Study and Reference Guide, Chapter 12: 802.11k/v/r/u/w/ai Amendments, page 434; CWAP-405Certified Wireless Analysis Professional Study and Reference Guide, Chapter 12: 802.11k/v/r/u/w/ai Amendments, page 435.