300-515 Exam Question 36
Refer to the exhibit. IPv4 traffic between location A and location B has previously experienced no congestion or packet drops. The hub R3 router was recently added to the network and connected to R1 and R2 over Frame Relay T1. Link A has just gone down, and an engineer is observing congestion on both of the R3 connected links. Which change must the engineer make to the network topology to fix the issue and prevent such congestion if link A goes down again?
300-515 Exam Question 37
Refer to the exhibit. As their network ages and traffic increases, the network-engineering team at a small company is concerned that links may degrade in performance over time, which makes the degradation difficult to detect before becoming widespread. The team decided to implement Ethernet OAM to monitor links to certain critical resources, such as the file server.
Which action must the team take so that remote OAM is alerted when a fault occurs?
Which action must the team take so that remote OAM is alerted when a fault occurs?
300-515 Exam Question 38
SIMULATION 4
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
Refer to the Tasks tab to view the tasks for this lab item
Refer to the Topology tab to access the device console(s) and perform the tasks.
Console access is available for all required devices by clicking the device icon or using the
tab(s) above the console window.
All necessary pre-configurations have been applied.
Do not remove any existing configurations from the devices, only those necessary to make the
appropriate changes required to fulfill the listed tasks.
Do not change the enable password or hostname for any device.
Save your configurations to NVRAM before moving to the next item.
Click Next at the bottom of the screen to submit this lab and move to the next question.
When Next is clicked, the lab closes and cannot be reopened.
Topology
Tasks
Routers R1 through R4 implement Ethernet Operations, Administration, and Maintenance operations.
Perform the below configuration on R1 and R4.
Configure E-OAM on interface E0/0.
Configure link monitoring:
- Monitor error frames
- Set a high threshold equal to 400
- Set threshold action equal to error-disable
The initial configuration with IP addressing has been completed. Do not change the configurations except to fulfill the abovementioned tasks.
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
Refer to the Tasks tab to view the tasks for this lab item
Refer to the Topology tab to access the device console(s) and perform the tasks.
Console access is available for all required devices by clicking the device icon or using the
tab(s) above the console window.
All necessary pre-configurations have been applied.
Do not remove any existing configurations from the devices, only those necessary to make the
appropriate changes required to fulfill the listed tasks.
Do not change the enable password or hostname for any device.
Save your configurations to NVRAM before moving to the next item.
Click Next at the bottom of the screen to submit this lab and move to the next question.
When Next is clicked, the lab closes and cannot be reopened.
Topology
Tasks
Routers R1 through R4 implement Ethernet Operations, Administration, and Maintenance operations.
Perform the below configuration on R1 and R4.
Configure E-OAM on interface E0/0.
Configure link monitoring:
- Monitor error frames
- Set a high threshold equal to 400
- Set threshold action equal to error-disable
The initial configuration with IP addressing has been completed. Do not change the configurations except to fulfill the abovementioned tasks.
300-515 Exam Question 39
SIMULATION 1
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
Refer to the Tasks tab to view the tasks for this lab item
Refer to the Topology tab to access the device console(s) and perform the tasks.
Console access is available for all required devices by clicking the device icon or using the
tab(s) above the console window.
All necessary pre-configurations have been applied.
Do not remove any existing configurations from the devices, only those necessary to make the
appropriate changes required to fulfill the listed tasks.
Do not change the enable password or hostname for any device.
Save your configurations to NVRAM before moving to the next item.
Click Next at the bottom of the screen to submit this lab and move to the next question.
When Next is clicked, the lab closes and cannot be reopened.
Tasks
CE1 and CE2 are customer premise equipment of the same customer that communicates with each other over L2VPN provider infrastructure comprising Provide Edge PE1, PE2, and P core routers.
Configure the PE routers to choose the configured Loopback 0 as its LDP identifier persistently.
Troubleshoot the PEs to establish a complete MPLS LSP path between them.
Troubleshoot and modify PE2 to ensure the configured L2VPN VC is up and passing traffic.
Initial configuration with IPv6 addressing has been completed. The candidate must not make any changes to the configurations except to fulfill the tasks listed above. Apply the solution with the minimum config.
P
PE1
PE2
CE1
CE2
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
Refer to the Tasks tab to view the tasks for this lab item
Refer to the Topology tab to access the device console(s) and perform the tasks.
Console access is available for all required devices by clicking the device icon or using the
tab(s) above the console window.
All necessary pre-configurations have been applied.
Do not remove any existing configurations from the devices, only those necessary to make the
appropriate changes required to fulfill the listed tasks.
Do not change the enable password or hostname for any device.
Save your configurations to NVRAM before moving to the next item.
Click Next at the bottom of the screen to submit this lab and move to the next question.
When Next is clicked, the lab closes and cannot be reopened.
Tasks
CE1 and CE2 are customer premise equipment of the same customer that communicates with each other over L2VPN provider infrastructure comprising Provide Edge PE1, PE2, and P core routers.
Configure the PE routers to choose the configured Loopback 0 as its LDP identifier persistently.
Troubleshoot the PEs to establish a complete MPLS LSP path between them.
Troubleshoot and modify PE2 to ensure the configured L2VPN VC is up and passing traffic.
Initial configuration with IPv6 addressing has been completed. The candidate must not make any changes to the configurations except to fulfill the tasks listed above. Apply the solution with the minimum config.
P
PE1
PE2
CE1
CE2
300-515 Exam Question 40
Refer to the exhibit. A customer is experiencing a VPN traffic outage: The VPN connection CustomerLMN between PEA and PEC is down. After debugging, the service provider network engineer found that the VRF RD and RT values are correctly configured on PEA and PEC, and MP-BGP peering is up between the PE routers. Which configuration resolves this issue?
